Is Hydrastar EOH Actuator Compatible With 2022 Chevy Silverado 5500 OEM Brake Controller

Question

Question:

I have a 2022 Chevy 5500 with the integrated brake controller, will this work with the Hydrastar?

asked by: Jeff S

0

Expert Reply:

According to Hydrastar, the # HBA16 is compatible with Chevy/GMC models 2017-present. This means you can use the actuator with your 2022 Chevy Silverado 5500 and you do not need the # HBA-CAM.

expert reply by: Robin H

0

Answer 1

Hey Kirk, yes the Deutsche Hydrapro CAM Adapter Module for Dexter and Hydrastar Electric Over Hydraulic Actuators #DH64FR would also work with a DeeMax actuator as these adapters are all basically the same thing which is a magnet that gets installed…

view full answer...

Answer 2

Hello Michael, thanks for reaching out. We should have the parts you need, and the DeeMaxx Disc Brake Kit #DE26AR may work for you, but there is no way for me to look up your camper online to know exactly what disc brake kit will fit. RV…

view full answer...

Answer 3

The integrated brake controller of your 2022 GMC Sierra 3500 has a hydraulic mode which would allow it to work with electric over hydraulic actuators without needing an adapter. With that said if for some reason the controller wasn't recognizing…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...