Replacement Strap For The Dutton-Lainson Hand Winch DL17021

Question

Question:

Can I replace the strap on the boat trailer hand winch?

asked by: Brian C

0

Expert Reply:

Yes you can replace the strap on the Dutton-Lainson Hand Winch # DL17021. For a replacement strap I recommend the # DL24260. This is a 20' long 2" wide strap rated for 2,600 lb max load.

expert reply by: Jesse M

0

Answer 1

Hi Berry, Thanks for your question. Based on what you've described, I'd recommend the Winch Ratchet Repair Kit by Dutton-Lainson #DL70475. This kit replaces the common ratchet components that can wear or become damaged over time, including…

view full answer...

Answer 2

The mounting pattern for the Dutton-Lainson Hand Winch - TUFFPLATE Finish - 2 Speed - Direct Drive - 2,000 lbs #DL14725 you were looking at is the exact same as your current DL1802A, but the overall dimensions of the winches are different. The…

view full answer...

Answer 3

For a replacement strap that will work great with your Dutton-Lainson Hand Winch #DL14627 I highly recommend the Dutton-Lainson #DL24249. This is a really durable 2 inch wide, 25 foot long strap with a breaking strength of 4,000 pounds. It includes…

view full answer...

Answer 4

The only real difference between using an integrated hub/rotor combo and a separate hub and rotor combo is that if something happens to the rotor and or hub on the separate hub/rotor, you can just replace the damaged component and not the entire…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacement Strap For The Dutton-Lainson Hand Winch DL17021

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching