Torque Spec for Legs of Curt Q20 Hitch to Head

Question

Question:

could you please tell me what the torque specs are for the curt q20 fith wheel hitch. its the puck system hitch but would like to no what the head unit bolt torque spec are. thanks,

asked by: Joe M

0

Expert Reply:

The torque spec for the legs of the Curt Q20 hitch part # C16530-16021 to the head of the hitch is 100 ft lbs.

expert reply by: Jameson C

0

Answer 1

It sounds like you are looking for a new motor for an RV slide out. I checked with my contact at Lippert Components, which makes the majority of OEM trailer and RV frames and slide-outs, and they do indeed have a direct replacement motor. You will…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

Hey Jerry, GM moved the placement of their puck systems starting with 2020 models so you are correct that the pucks would have the hitch not sit directly over the axle. GM did the math and made sure that this placement wouldn't adversely affect…

view full answer...

Answer 7

Hey Jordan! Based on your measurement you have a Lippert 1116 or 1716. If you want to confirm that feel free to send me the S/N on your pin box. The Gen-Y Nomad you were looking at is for the Rhino Box so that is not a fit. What you need is the Gen-Y…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 11

Hey Frank. I can give you the dimensions of the shank on the B&W Continuum item #BW28FR but you're going to need to take the measurements on your Silverado 3500 to confirm the tailgate will open. From the hitch pin hole to the center of the…

view full answer...

Answer 12

Hi Glen, It will depend on what the GVWR (gross vehicle weight rating) is of your trailer to determine which B&W 5th wheel to gooseneck adapter will work best for you. Fifth wheels and gooseneck trailers go off of pin weight instead of tongue…

view full answer...

Torque Spec for Legs of Curt Q20 Hitch to Head

Continue Researching