Compatible Rear Anti-Sway Bar For A 2019 Ram 3500 4WD

Question

Question:

Will the RM73FR anti sway bar fit a Ram 3500 4wd with a 6.4L Gas engine and factory air suspension? Hellwig does not due to the muffler being in the way of the passenger side frame mount and connector arm. But if the Roadmaster fits this version of my vehicle, Im ready for it.

asked by: Tom

1

Helpful Expert Reply:

Roadmaster's fitguide lists that the Roadmaster Rear Anti-Sway Bar # RM73FR will fit your 2019 Ram 3500 4WD with factory air suspension.

expert reply by: Kevin C

1

Answer 1

No, it won't and it's because of the exhaust. The Hellwig Big Wig Rear Anti-Sway Bar item #HE24MR will only work on the diesel models of the 2024 Ram 3500. It is not compatible with your 6.4 Hemi model. The Roadmaster Rear Anti-Sway Bar item…

view full answer...

Answer 2

Yes, the Hellwig Big Wig Rear Anti-Sway Bar - 1-5/16" Diameter #HE24MR is confirmed to fit the 2023 Ram 3500 models with the 6.7L diesel engine. This will work with 2WD/4WD models and is fine with dually models as well.

view full answer...

Answer 3

The Draw Tite part #DT36MR sticks out further than the Curt #C73ZV that fits your 2022 Ram 2500.

view full answer...

Answer 4

Rene, you unfortunately are not going to be able to use both air bags and SumoSprings like #SS68RR at the same time. The air bags fit inside the coil springs on the bag so there would not be room to also have the SumoSprings. Even if you were able to…

view full answer...

Answer 5

The TorkLift StableLoad Suspension Upgrade w Quick-Disconnect #TLA7310S should fit just fine with the Air Lift air bag kit and RAS on your 2021 Ram 3500. My concern though is that you've either already worn out the factory suspension on your…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Compatible Rear Anti-Sway Bar For A 2019 Ram 3500 4WD

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching