Is There A Plug-And-Play Brake Controller Wire Harness For A 2018 GMC Canyon

Question

Question:

Is there a plug into brake controller wiring harness available for after market GMC canyon controller?

asked by: Phil

0

Expert Reply:

There is not a plug-and-play style connector for an aftermarket brake controller for a 2018 GMC Canyon so you would have to splice into the factory wiring. You'll need to look for the cold side of the brake light switch by checking the wires coming off of the brake pedal with a tester # PTW2993. The wire that lights up only when the brake pedal is depressed is your brake light switch wire. If you can't find it or the wire is too thin of a gauge to splice into then you can use the Roadmaster Stop Light Switch Kit # RM-751472 to get the brake light signal instead.

If you don't want to splice into the wiring you could use the Curt Echo In-Line Wireless Brake Controller # C79DR, which connects inline with your factory 7-way and is controlled by an app.

expert reply by: Kevin C

0

Answer 1

On the Tekonsha Prodigy P3 Brake Controller #90195 (great choice) the black wire is for 12V power, the blue wire is for brake output to the 7-Way connector, the red wire is for brake switch on the vehicle, and the white wire is for ground. Based on…

view full answer...

Answer 2

Your 2018 Chevy Colorado has the brake controller wiring ran under the dash of the truck but there isn't an adapter that uses a connector. Reason being there's only 4 blunt cut wires under your vehicle dash for the brake controller wiring and…

view full answer...

Answer 3

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Hey Ray, thanks for reaching out. If you are set on placing the propane tank inside the toolbox, it can be done safely as long as the box is properly vented at the bottom. Propane is heavier than air, so if there is ever a small leak it will settle…

view full answer...

Is There A Plug-And-Play Brake Controller Wire Harness For A 2018 GMC Canyon

Products Featured in This Question

Continue Researching