Replacement Trailer Clearance Light that Fits in Wedge Mount

Question

Question:

Looking for replacement red marker light with this wedge housing , need it for the driver’s side . What do you have for a replacement. Thanks

asked by: Ed S

0

Expert Reply:

Thanks for the picture of your trailer clearance light. It's one of two options depending on how long it is. It's the part # MCL75RB if the light is 3-15/16 inches long or # AL91RB if it's 2-1/2 inches long.

expert reply by: Jameson C

0

Clearance Light Trailer
(click to enlarge)

Answer 1

We have the Optronics Incandescent #MC65RB and Optronics Thinline LED #MCL75RB that use a red lens. The Optronics Incandescent #MC65AB and Optronics ThinLine LED #MCL75AB have an amber lens. A Optronics ThinLine LED #UCL65CB uses a clear lens with…

view full answer...

Answer 2

According to Optronics the GloLight Thinline LED Trailer Clearance or Side Marker Light - Submersible - Rectangle - Amber Lens #MCL165AB has 10 diodes in the light. The quantity for this item is one, so you would receive one light if you ordered a…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Trailer Clearance Light that Fits in Wedge Mount

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching