Fulton Marine Jack # HD50000101 Inner Tube Hole Spacing

Question

Question:

I need to know the span between the adjustment holes going vertically on the base inner square tube. I have no picture to add, I am submitting this to my companys purchasing department, with the quote I received today from Stacy at 79515. Thanks,

asked by: James B

0

Expert Reply:

I went out to our warehouse and pulled off the inner tube/base of the Fulton Marine Jack # HD50000101 and measured from the top of the base out to each of the holes. The diagram I have below shows the measurement from the base to the center of each hole.

expert reply by: Kevin C

0

HD50000101 Base Hole Spacing
(click to enlarge)

Answer 1

While your frustration is understandable and we have a solution for you, I wouldn't be able to tell you with absolute certainty that using the Stromberg Carlson Electric Trailer Jack #JET-3755 will stop your tailgate from hitting the jack. The…

view full answer...

Answer 2

I reviewed some choices which would meet your individual needs and were all non-electric, drop leg, and excellent ground clearance. There were a number of similar jacks, but only one that would mount to your 6” trailer frame. I ordered one from the…

view full answer...

Answer 3

We do have a very similar 5K trailer jack like the Pro Series #PS1400800383 but that is a bolt-on installation instead of a weld-on. The Fulton Marine Jack #HD50000101 is also rated for 5K and it has a lift of 14" as opposed to 15" like the…

view full answer...

Answer 4

I believe you're referring to is the Pro Series Round, Pipe-Mount Swivel Jack #PS1401440303, and the pipe this mounts too cannot be bolted on, it must be welded on. For this reason I recommend the Fulton Marine Jack - Square Tube, Fixed Mount…

view full answer...

Answer 5

A trailer jack only lifts part of the weight of the trailer and not the whole 10,000 pounds of your trailer. A 10K trailer would have a tongue weight of around 1,000 to 1,500 pounds. But the higher the capacity of the jack the easier it is for the…

view full answer...

Answer 6

The Fulton Marine Jack #HD50000101 mounting plate has a 1/4" thickness.

view full answer...

Answer 7

I have a different option for you, but the Trailer Valet JXS Jack #TV64FR is not recommended for use in salt water per my contact at Trailer Valet. Instead you will want to go with the Fulton Marine Jack - Square Tube, Fixed Mount - 28" Lift -…

view full answer...

Answer 8

Sounds like your trailer wiring does not have a ground circuit for it's connector. The easy solution for that is to run a wire from the ground pin of the connector to the trailer's frame. Your trailer electronics should work a little better…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Fulton Marine Jack # HD50000101 Inner Tube Hole Spacing

Featured Help Information

Miscellaneous Media

Continue Researching