Availability Of M16 Threaded Hitch Pin With Lock

Question

Question:

My bike rack uses an M16 threaded hitch bolt with a cotter pin. I am looking for an M16 threaded hitch bolt with lock. Do you have anything like that?

asked by: Phil C

0

Expert Reply:

We have just the thing. The etrailer threaded hitch lock # e99047 uses a M16-2 bolt. This has a pin diameter of 5/8" with a 2-5/8" span.

expert reply by: Jesse M

0

Answer 1

Kuat accessories, such as the Kuat Hi-Lo Hitch Extender - 2" Hitches - 7" or 10" Extension - 2-1/8" Rise/Drop #HL20B, use Kuat-specific threading for their threaded anti-rattle bolts. Kuat was not able to tell me the size of their…

view full answer...

Answer 2

Hey Dana, thanks for reaching out, although I'm sorry to hear about the problems you're having. What accessory were you trying to install into the Kuat Hi-Lo Hitch Extender #HL20B, and do you have any photos of the obstruction you mentioned?…

view full answer...

Answer 3

At one point, Kuat had specific lock numbers available but they have changed that recently in order to make ordering locks easier for their bike racks; due to this, specific lock numbers are not something Kuat makes available. The correct lock is…

view full answer...

Answer 4

IF you're worried about the Kuat Sherpa #SH22G melting because of the exhaust, I suggest using the Hi-Lo adapter #HL20B. This will extend your rack up/down and out. I really do like the Sherpa and don't think that you'll avoid the…

view full answer...

Answer 5

The Kuat Hi Lo adapter part #HL20B has a threaded hitch pin design where it installs into the vehicle hitch, so a Kuat hitch lock like the part #HLT would securely lock the adapter to the vehicle hitch.

view full answer...

Answer 6

Bike rack manufacturers try to thread their pins and locks as uniquely as they can in order to make sure you use their product. The Advantage Threaded Trailer Hitch Receiver Lock #HE6033 has not been tested with the Kuat Transfer bike racks but it is…

view full answer...

Answer 7

I had our warehouse measure the thread pitch of the Swagman Anti-Rattle Hitch Lock #S64027 you were looking at and it has a 5/8" x 11 thread pitch. We do have the Threaded Anti-Rattle Hitch Pin Lock for etrailer Cargo Carriers #e99047 which has…

view full answer...

Answer 8

Yes, there is a way to secure the accessories to the Yakima EXO Swing Away Cargo Carrier item #Y72VR. The Swing Away base has Yakima's Same Key System (SKS) locks built in that secures the accessories to the base. These cores are included but can…

view full answer...

Answer 9

You can use an anti-rattle device such as #SHP2082 as long as the shank on the bike rack is hollow. If it is not hollow then use anti-rattle device #MPG908. I have included a link to a video review of device #MPG908 for you. It is also possible that…

view full answer...

Answer 10

Yes you should indeed use the washers for the hitch pin with the 24x60 etrailer Cargo Carrier for 2" Hitches #e98874. Reason is, the washers help distribute the pressure on the anti-rattle bolt, especially when tightening them down. So what you…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Availability Of M16 Threaded Hitch Pin With Lock

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching