Will The Dexter DX Brake Actuator Replace a Titan Brake Actuator For Drum Brakes?

Question

Question:

I have an older Titan brake actuator p/n 68-003-00. Will this work for a replacement? I can’t find anything that says it will work.

asked by: Nick S

0

Expert Reply:

Yes, the Dexter DX Series Electric Over Hydraulic Brake Actuator for Drum Brakes # K71-650 will replace your Titan 68-003-00 actuator.

expert reply by: Bud M

0

Answer 1

The Dexter Zinc-Plated Brake Actuator #T43397007K is a replacement for the DICO/Titan Model 60 actuator. As Dexter bought Titan this is now their version of the Model 60 actuator. This will work with the Hydraulic Trailer Brake Kit #AKUBRK-35-D but…

view full answer...

Answer 2

The DeeMaxx Disc Brake Kit #DE82FR with the Maxx coating has a salt spray rating of over 1,000 hours while the DeeMaxx Disc Brake Kit #DE54VR with the Stainless construction isn't rated for salt spray, but when I spoke with the owner he said the…

view full answer...

Answer 3

Hello Maxim. I do have a video that I think you will find helpful, but we do not have a video showing installation of the exact Dexter Actuator #T47457107K that you mentioned. We do have a video showing installation of a similar bolt-on actuator, the…

view full answer...

Answer 4

The best option would be to go with Disc Brakes #DE66YR. These are the best option as they repel water better than other trailer brakes and will offer superior braking. This will require the Zinc-Plated Brake Actuator #T47457107K and Brake Line Kit…

view full answer...

Answer 5

The actuator that you have referenced, #T47154007K, does not have a reverse lockout. However, if you were to add one using #T4748800, it works by blocking the flow of fluid back to the brakes when the tow vehicle is placed in reverse. There is no…

view full answer...

Answer 6

I have attached an install video to this page for you to check out that you can use as a guide for installing the Titan Model 60 actuator part #T43397007K that you referenced. The video shows a very similar Demco coupler part #DM72VR but the couplers…

view full answer...

Answer 7

We do have a 7k disc brake surge actuator that fits a 2 inch ball with the Demco part #DM62VR which will easily fit in place of what you have now. It's not a Titan but the Demco actuators are super solid

view full answer...

Answer 8

Unfortunately, the rubber boot isn't available as a separate item. If you decide to replace the entire master cylinder, I'd be happy to recommend a replacement if you reply with the model of hydraulic brake coupler you have. To clean the…

view full answer...

Answer 9

Hi Jeff; can you send me a picture of the coupler on the ball? I'm assuming this is a 2" ball on your ball mount. It sounds like it is really close but difficult to say with just a description. With the Drop-N-Go coupler mechanism you should…

view full answer...

Answer 10

For a disc brake model with an electric reverse lockout solenoid you can use #099-175-20.

view full answer...

Answer 11

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 12

The Dexter Brake Actuator part #099-175-20 replaced the Titan 60 that has a master cylinder with a fitting at the end. The fitting is a 3/16 inverted flare where the brake lines connect to. You do not need an extra fitting when you use the actuator.…

view full answer...

Will The Dexter DX Brake Actuator Replace a Titan Brake Actuator For Drum Brakes?

Product Page this Question was Asked From

Continue Researching