Replacement Brake Assemblies for Big Tex 14ET Trailer with 7k Axles

Question

Question:

Hi, I need brake assemblies for a Big Tex 14ET 14k trailer with 2 7,000lb axles. Could you please let me know fitment? Thanks

asked by: Nick S

0

Expert Reply:

Since we know you have 7k axles the correct brake assembly set you'd want is the etrailer set part # AKEBRK-7-SA and you'd be set. These are self adjusting too which means you won't ever have to manually adjust brake assemblies.

expert reply by: Jameson C

0

Answer 1

Dexter brake assemblies like the part #23-458-459 are essentially the best ones on the market. They use the best materials and and incredibly reliable and well-made. That being said the etrailer.com brand assemblies part #AKEBRK-7-SA are also very…

view full answer...

Answer 2

From the sound of your trailer has the common 5-bolt brake flange (see attached photo to verify) and the standard 12 inch x 2 inch brake assemblies. With this information, you will be able to swap out your hubs, drums, and brakes with the following…

view full answer...

Answer 3

In order to choose the correct replacement braking assemblies for a 2008 PJ Dump Trailer you'll need to know the axle capacity. It looks like most trailers of this size have anywhere from a 5,200 lb to 7,000 lb axle and in which case you'd…

view full answer...

Answer 4

While I was unable to confirm who manufacturers the Defender 2 brake away system on your 2021 Big Tex 60EC. I do agree that the Bright Way Push-to-Test Trailer Breakaway Kit #3802346 does look identical minus the decal and they have the same wiring…

view full answer...

Answer 5

In order t lift your Big Tex 22 GN HD you would have to flip your leaf springs so they are on top of your axles instead of below. This can be done with the Dexter Trailer Springs Over-Under Conversion Kit, part #K71-385-00. This kit only works with…

view full answer...

Answer 6

We only carry the springs for those heavy duty style ramps. For the springs we have the Ramp Spring - 2K Torque for 1-1/2" Shaft - left hand #RS16933LH and corresponding right hand #RS16933RH. The other parts will need to be either straightened…

view full answer...

Answer 7

I recommend the Redline Ramp Spring - 2K Torque for 1-1/2" Round Shaft for the new ramps on your trailer. You will need the #RS16933RH for the right and #RS16933LH for the left hand side. One spring per ramp should be adequate without overdoing…

view full answer...

Answer 8

The Left Hand #RS16933LH and Right Hand #RS16933RH are universal fits and will work with a 1-1/2" round shaft. As long as this matches your specs you'll be good to go! I've attached some videos for you to check out as well.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Replacement Brake Assemblies for Big Tex 14ET Trailer with 7k Axles

Product Page this Question was Asked From

Continue Researching