Replacement Handle For Dutton-Lainson DL3200 Winch

Question

Question:

Are the Dutton Lainson ratcheting handles compatible with the DL 3200 winch ?

asked by: Bill D

0

Expert Reply:

The ratcheting handle is not compatible with the DL3200 winch; the correct replacement handle for the Dutton-Lainson DL3200 winch is the following:

- Replacement Quick Attach Winch Handle for Dutton Lainson Winch # DL70330

expert reply by: Kyle S

0

Answer 1

If you were looking for a replacement handle, the hole opening on the Replacement Quick Attach Winch Handle for Dutton Lainson Winch - 9-1/2" #DL70330 will measure 15/32" by 5/8" and looks like it will be a good replacement for your…

view full answer...

Answer 2

If the charge light of the breakaway system part #PS50-85-320 is staying on the charging state that means that box is drawing power to some extent. Although your battery seems like it's fully charged the 12 volt power circuit is still able to…

view full answer...

Answer 3

That number doesn't give me a cross-reference. To get a replacement you will need to pull the bearings out of the hub and on the face of both the inner and outer bearing there will be a number printed on the bearing face. If you can give me those…

view full answer...

Answer 4

When it comes to choosing a winch for a boat trailer, there are a few general rules we can use. The boat-size-to-winch capacity is generally 2 to 1. With good rollers and short winching distances, the ration can increase to 3 to 1 and with wooden…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Steve, the size of the slot in the Winch Replacement Handle, #DL70334, is 3/8 inches wide by 1/2 inches long. What winch do you have that you are looking for a replacement handle for?

view full answer...

Answer 7

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…

view full answer...

Answer 8

Most of the winches in the 2,500 lb. category are going to use the same type of handle. There are always exceptions but most use a common size. For your situation I recommend the 9-1/2" Long Winch Offset Replacement Handle by Dutton-Lainson part…

view full answer...

Answer 9

The Replacement Handle for Dutton-Lainson Single Speed Hand Winch #DL70305 you like has an attachment hole that is 1/2" x 3/8". We do not have anything that is the exact 5/8" x 7/16" you are needing. The closest we have would be…

view full answer...

Answer 10

I went and pulled a Dutton Lainson Winch Handle part #DL70326 from our warehouse to measure the slot and found the dimensions to be 1/2 of an inch by 3/8 of an inch. If the dimensions of your winch handle are the same this handle should work well for…

view full answer...

Answer 11

There are a couple of handles that you can use for your Fulton T1801 winch. For a 9 inch long handle use #F501109. For an 11 inch handle use #F501101. The longer the handle the easier it is to crank but it's easier to crank a shorter handle…

view full answer...

Answer 12

Hey Kris, the Dutton Lainson winch part #DL15440 does not come with a strap so you will need to order one with it. The part #DL24250 will work great with this winch as it is correct width, is 25 feet in length, and has a capacity of 3,700 lb WLL and…

view full answer...

Replacement Handle For Dutton-Lainson DL3200 Winch

Product Page this Question was Asked From

Continue Researching