Can 12V Outlet In Rear Of 2014 Nissan Rogue Be Used For Wiring Harness Power
Updated 03/07/2014 | Published 03/06/2014
Question:
My new Rogue has a 12vdc power outlet on the passenger side near the tailgate. Can I just use that circuit instead of running a wire all the way up to the battery?
asked by: William B
Helpful Expert Reply:
We do not recommend using the 12 volt power outlet in the rear area of your 2014 Nissan Rogue when connecting a circuit protected wiring harness like part # C56033 because it has a higher rated fused circuit that could allow more power to be drawn through the wiring harness and potentially damage either the harness or the vehicle. This harness has not been tested with the installation using the rear power source and could void the warranty. I have attached a link to an installation video of this harness being installed on a 2014 Nissan Rogue.
Product Page this Question was Asked From
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Vehicle End Connector
- Powered Converter
- No Tow Package
- 4 Flat
- Plug and Lead
- Plug-In
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Video: Review of Seaflo RV Toilets - Standard Height - SE85MR
- Shop: Seaflo RV Toilet - Elongated Seat - Slow Close Lid - Polypropylene - White
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Video: Installation: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector on a 2011 Audi A4
- Shop: etrailer Hitch Pin Alignment Collar for Hitch Accessories - 2" Hitches
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Video: Best 2018 Nissan Rogue Roof Rack Options
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2019 Nissan Rogue
- Video: Install: etrailer Trailer Hitch Receiver on a 2018 Nissan Rogue
- Shop: Base Plate for Tow Bar
- Shop: Roof Rack
- Shop: BOLT brand vehicle and hitch locks
- Shop: Brake Controller
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
- Video: DIY Install: Draw-Tite Max-Frame Trailer Hitch Receiver on your 2017 BMW X1
- Q&A: Where to Connect 12 Volt Power For 4-Way on 2023 Kia Sportage Hybrid
- Shop: Vehicle Tow Bar Brake System
- Q&A: Finding The Brake Controller Input Wire On a 2018-2019 Chevrolet Equinox
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: How Long Does It Take To Install the Universal Installation Kit for Trailer Brake Controller ETBC7
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Will Installation of Oris Hitch on 2019 Volvo XC90 T6 Require Trimming/Interfere With Kick Sensor
- Q&A: Estimated Installation Time for B&W Turnoverball Underbed Gooseneck Trailer Hitch # BWGNRK1117
- Q&A: Does the Oris AK41 Hitch Block the Foot Sensor on a 2021 Volvo XC90?
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Article: How to Measure for Trailer Hitch Drop
on Custom Fit Vehicle Wiring
