Recommended 7-Way Connector for a 2019 Subaru Ascent

Question

Question:

I need to change from a 4 pin to 7 pin trailer plug on my 2019 Subaru Ascent. there was a trailer harness plug in in the trunk which I used to install the 4 pin plug. What do I need to buy and do you have installation instructions.

asked by: Paul M

0

Expert Reply:

Yes, there is a plug in 7-way connector for your 2019 Subaru Ascent. It is the Tekonsha OEM Replacement Vehicle Wiring Harness with 7-Way Trailer Connector item # 118290. It uses the same connector as the 4-ways. I have linked the installation instructions below.

expert reply by: Jerred H

0

Answer 1

Yes, it can. To add a 7-Way to your 2021 Subaru Ascent you will need the Tekonsha OEM Replacement Vehicle Wiring Harness item #118290. This will provide you a 7-way connector and all the wiring and hardware you will need to install it and connect the…

view full answer...

Answer 2

When rotating tires like the #AM10303 on your triple axle trailer I recommend using the X pattern. This means you will swap the front driver side tire with the back passenger side tire, the front passenger side tire with the back driver side tire,…

view full answer...

Answer 3

The correct replacement control module for your Kwikee Steps with Control Module 909513 is the Lippert Components Kwikee Control Unit part #LC379606.

view full answer...

Answer 4

Hello Benjamin, We used to have the Amber lens for the 99 series clearance light, but we no long have it available because it is no longer being made. With that being said, I recommend swapping the light out for the Trailer Clearance or Side Marker…

view full answer...

Answer 5

There are two different 7-way trailer wiring harnesses for a 2019 Subaru Ascent dependent on whether or not you have the factory tow package. If you do have the factory tow package then you should be using the Tekonsha OEM Replacement Vehicle Wiring…

view full answer...

Answer 6

When it comes to installing a trailer brake controller in your 2019 Subaru Ascent The Redarc Tow-Pro Elite Trailer Brake Controller - 2 Braking Modes - 1 to 3 Axles - Proportional #RED44FR and The Tekonsha Plug-In Wiring Adapter for Electric Brake…

view full answer...

Answer 7

For a portable system, I suggest the Go Power Portable Solar Panel with Digital Solar Controller, #34282730. This is a 130 watt foldable solar panel that allows you to place it where you choose to for maximum sunlight. Under optimum conditions, this…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Recommended 7-Way Connector for a 2019 Subaru Ascent

Continue Researching