Replacement Bearings and Seals for 2019 Grand Design Imagine 22RBE With 3k Dexter Axle

Question

Question:

Which wheel bearings and grease seals do I need for a Grand Design 22RBE with Dexter Axles. Dex# 8389381 120120 D30

asked by: Carl B

0

Expert Reply:

What you have on your 2019 Grand Design Imagine 22RBE is a 3,000 lb Dexter axle. The inner bearing is # LM67048 and the outer bearing is # L44649. The correct grease seal is the # RG06-050 (10-19).

expert reply by: Robin H

0

Answer 1

You will need the Bearing Kit #BK2-100 for each of your hubs on your 2019 Grand Design Imagine XLS 18RBE travel trailer. With doing all 4 hubs it will be much easier with a Seal Puller #PTW1219 and Installation Set #PTW83020 to replace all the…

view full answer...

Answer 2

Yes, for Dexter part number K08-247-1G you'll need the Dexter Trailer Hub & Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased #84546UC3-EZ.

view full answer...

Answer 3

Hey Jared! Thank you for providing those part numbers. You have #LM67048 outer and #25580 inner bearings with a #DX72UR (K71-305-00) grease seal. The correct Timken bearing kit is the #TMK72VR. If you need anything else feel free to reply below.

view full answer...

Answer 4

John, I do believe we have something for you, but without any dimensions of the center cap it's going to be a bit difficult to say for sure, but from the looks of it the Trailer Wheel Center Cap Plug #AM90082 looks like it'll work. This…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Replacement Bearings and Seals for 2019 Grand Design Imagine 22RBE With 3k Dexter Axle

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching