Replacement Master Cylinders for UFP A-84 Actuator

Question

Question:

Hi, Im looking to replace my existing brake actuator and brake cylinders. The brake actuator I have is a UFP A-84. Would you have that or a equivalent? Thanks.

asked by: Craig C

0

Expert Reply:

For replacement master cylinders for your UFP A-84 you would need the part # DX44FR for a disc brake or # TK71-756-00 for a drum brake setup.

expert reply by: Jameson C

0

Answer 1

When bleeding the brakes on a surge actuator, such as the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout #DX56FR, you want to start by making sure there is fresh fluid in the reservoir then press a screw driver against the rod in the access…

view full answer...

Answer 2

Judging from the photo, it does look like the #DX44FR that you were looking at is the correct replacement part you need. This is the replacement master cylinder for the A-60, A-75, A-84, A-160, A-200, XR-84 and XR-200 series of Dexter actuators, in…

view full answer...

Answer 3

The Replacement Master Cylinder Assembly for Dexter Brake Actuators - Disc Brakes #DX44FR can be used to replace the A-60 master cylinder and is designed to fit on a variety of Dexter/UFP brake actuators.

view full answer...

Answer 4

There are a couple options that could be causing this issue with your Replacement Master Cylinder Assembly #DX44FR. The first would be an incorrect fitting. The female brass fitting exiting the solenoid or master cylinder body of the K71-757-00…

view full answer...

Answer 5

A great choice for your boat trailer is the LED Trailer Light Kit for Trailers Over 80" Wide #TL16RK. This kit includes 2 tail lights which serve 8 functions (Stop, turn, tail, side marker, rear clearance, side reflector, rear reflector, and…

view full answer...

Answer 6

Yes, the Solenoid Valve #T4748800 will allow you to add a reverse lockout on your UFP XR-84. We do also have the Replacement Master Cylinder Assembly #DX44FR which has a built in solenoid if you are needing to replace your master cylinder as well.…

view full answer...

Answer 7

If the air bubbles aren't ever stopping that indicates that air is getting introduced into the brake lines. Most likely through a bad master cylinder but since we know yours is a new part #T1777401 that would make me think that most likely you…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Master Cylinders for UFP A-84 Actuator

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching