Is There Torque Rating for Assembly of Malone EcoLight Trailer

Question

Question:

what torque should the frame assembly bolts be tightened to?

asked by: R L

0

Expert Reply:

I checked with Malone and the bolts that hold the frame of the Malone EcoLight trailer part # MAL43FR do not have a torque spec rating. So you would just want to get them hand tight with an appropriate size wrench/ratchet.

expert reply by: Jameson C

0

Answer 1

Hey Chuck, Malone has a spare tire and mount for the Malone EcoLight Sport Trailer for a Heavy Kayak #MAL73FR with part #MAL33FR. It's just a simple U-bolt that you'll use to clamp the wheel to the frame of the trailer, just like the picture…

view full answer...

Answer 2

Hey Russell, good question. It really comes down to what you’re carrying and how many boats you want on the roof. The V-style carriers are more of a “keep it simple” setup. They hold the kayaks flat, side-by-side, which is great for stability and…

view full answer...

Answer 3

Hello Keith, thanks for reaching out. Cutting the tongue on your Malone #MPG460G trailer is an option if you are wanting to shorten the tongue only a few inches. You could un-bolt the coupler and disconnect the wiring and have a section of tongue cut…

view full answer...

Answer 4

Hello again and thank you for your questions. To answer your first question, yes, it is possible to place the bunk kit #MPG561 on the 2nd Tier Load Bar System #MPG474. That said, the bunk kit weighs about 23 lbs, so that combined with the 90 lb kayak…

view full answer...

Answer 5

Yes, they can! The Yakima EasyRider Double Decker Trailer item #Y08129 has been designed to be submerged. The bearings are sealed so you won't have to worry about swapping them out. The Yakima Rack and Roll Trailer item #Y08107 didn't have…

view full answer...

Answer 6

The Malone MicroSport Trailer #MPG460G does have the 1.98 inch inner diameter hub. I confirmed this with the manufacturer. To add bearing buddies, you simply need the #BB1980A for chrome or #BB1980A-SS for stainless steel. You will not need to…

view full answer...

Answer 7

I spoke with my contact at Malone who said that the coupler height of the Malone MicroSportXT Trailer #MPG460XT is 15". When we installed the Draw-Tite Max-Frame Trailer Hitch Receiver #76138 on a 2017 Mazda CX-5 the coupler height (from the…

view full answer...

Answer 8

Hey Daniel, that is super frustrating that your Malone trailer part #MAL73FR did not come with instructions but I attached a link to them on this page for you to check out. Check them out and let me know if you still have questions.

view full answer...

Answer 9

Yakima does not recommend backing their Rack and Roll trailers like the #Y08107 you mentioned into water as the bearings aren't sealed and neither are the electrical connections. Your best option would be to back it right up to the waters edge…

view full answer...

Answer 10

Both the Yakima Rack and Roll Trailer #Y08107 and Malone MicroSportXT Trailer #MPG460XT will work for you to carry your two Hobie kayaks, but I recommend the MicroSport XT because it is the better value of the two trailers. The biggest difference…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...