What Are the Hole Spacing Dimensions for the Optronics 7-Way Trailer Harness Plug Protector

Question

Question:

Hole pattern dimensions?

asked by: Justin

0

Expert Reply:

The Optronics 7-Way Trailer Harness Plug Protector # ACP7B has mounting hole spacing of 2-3/4" side to side and 1-1/4" up and down. This can be attached with screws, bolts or some people have even just zip tied it to their trailer tongue.

expert reply by: Scott S

0

Optronics 7-Way Trailer Plug Protector Hole Moutning Measurements
(click to enlarge)

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 3

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 4

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 5

No, it does not James. The etrailer Electric Trailer Jack item #e22QV includes a 7-way connector and snap pad but not cover. The plastic housing will keep water from getting inside and damaging the controls. All of the buttons are covered in a…

view full answer...

Answer 6

Hey Richard. welcome back! The Go Power Pure Sine Wave Inverter Charger #GP75QR does not include the display. You will need the Go Power PowerTrak Screen #GP64XR to go with it. You will also need the #GP74XR, #GP84XR, and #GP24XR to make all of your…

view full answer...

Answer 7

I do have a couple options for you to consider. The first is the Fastway Tethered 7-Way Trailer Connector Cover #FA82-00-3315. This is a rubber cover that tethers to the 7-way that you can use to cover the end of the connector. Next is the Optronics…

view full answer...

Answer 8

I recommend at least 6" of clearance from the top of your bed rails on your 2021 Ram 3500 to the underbelly of your gooseneck or 5th wheel trailer. If using a gooseneck trailer and if you have the factory in bed prep/puck system there are…

view full answer...

Answer 9

Hi Jordan, You definitely want to replace your 11 inch long equalizer with the same length, the Equalizer for 2" Wide Slipper Springs - 11" Long #TREQ1304. Going with a longer equalizer will result in the not being in the correct position…

view full answer...

Answer 10

Good afternoon Trevor, thanks for stopping by our (online) shop. The Trailer Valet JXC Trailer Jack w/ Footplate and Drill Powered Option - 1.6K #TV94FR does have a universal bolt pattern that works with just about anything, and it would 100% fit the…

view full answer...

Answer 11

Hey Alison, thanks for reaching out! I looked through our whole selection of hinges but none of them match the exact design that you all already have on your Aluma trailer. What I recommend doing is using a whole different strap since you're…

view full answer...

What Are the Hole Spacing Dimensions for the Optronics 7-Way Trailer Harness Plug Protector

Product Page this Question was Asked From

Continue Researching