Replacement Taillights For 2020 TrailStar TXXU1648P

Question

Question:

Need a tail light for my 2020 TrailStar TXXU1648p stock# 1117855 Can you help?

asked by: Jim C

0

Expert Reply:

Thanks for the picture!

Based on the picture it looks like you need the ONE LED # STL0067RPG for the driver side, or # STL0066RBG for the passenger side or your 2020 TrailStar TXXU1648P.

expert reply by: Samuel C

0

Pic Of Taillight On 2020 TrailStar TXXU1648P
(click to enlarge)

Answer 1

It would appear you are needing the ONE LED Trailer Tail Light Driver #STL0067RPG and Passenger #STL0066RBG for your 2008 Trailstar trailer carrying your Bass Tracker 175 TXW boat. These lights both use the 3 prong plug in like you have included in…

view full answer...

Answer 2

Would you be able to send me some pictures of what your current lights look like and the triangular plugs that you mentioned so I can help you get something that works best?

view full answer...

Answer 3

I may have a solution for you depending on the type of connector you have. The Optronics Aero Pro Combination Trailer Tail Light item #ST37RB you need is 7 7/8" long by 3 1/4" wide. We have two lights of the same size that attach by plugs.…

view full answer...

Answer 4

In regards to trailer tail lights, a common mistake that people make is not unplugging them prior to launching the trailer. The reason that this is important has to do with not only the mixing of electricity and water but also the rapid cooling. If…

view full answer...

Answer 5

It could be possible that your 2012 Boat trailer is wired with a wishbone style harness. Similar to Item #A25W2GWB. This type of harness just allows the installer to run each side separate rather than splicing and running extra wires across the…

view full answer...

Answer 6

Hey Pharon, unfortunately there aren't any adapters that are going to allow you to use a 7 (what I'm assuming you have on your Jeep) to a 5 way round. What you can do instead is cut off the 5 way on your trailer and swap it with the Hopkins…

view full answer...

Answer 7

You can use a standard 5-pole trailer connector, you'll just need to wire it a certain way. The #HM47900 you referenced is the vehicle side connector, you need the trailer side connector like part #HM47910, which would wire as shown in the…

view full answer...

Answer 8

A standard 5-way like the part #HM47910 would work great to replace what you have. You'd just run all of the white wires that you have (all three) to the single white wire of this connector, both the brown wires to the single brown of the…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Replacement Taillights For 2020 TrailStar TXXU1648P

Product Page this Question was Asked From

Continue Researching