Parts To Rebuild Obsolete Hub For 3/4" Straight Spindle

Question

Question:

Looking for two 5 stud HUBS for a 3/4 axel.

asked by: Osberto A

0

Expert Reply:

3/4" axles are pretty old and as such there are no longer replacement hubs available.

As long as it's just the bearings and/or races damaged in your hubs you can rebuild them with two # LM11949 and two # LM11910 per hub allowing you to keep using it.

If the physical hub is damaged, which is not very common, then you need to search resale websites to find a replacement, or you'll be looking for a complete replacement axle to get you something with replacement parts readily available.

expert reply by: Samuel C

0

Answer 1

Unfortunately, we do not have any trailer hubs with the bearings that you need. Would you be open to replacing the entire axle? This would be the only option we have for you. If so then I would need you to measure the distance between each hub face…

view full answer...

Answer 2

Hello Ross, thanks for reaching out. We do carry the 3/4" ID bearings part #TMK36FR, but I am sorry to say we do not offer a hub for a 3/4" straight spindle. That spindle size is now obsolete, and I am not aware of any hubs made in that…

view full answer...

Answer 3

The closest standard axle we have available to the dimensions that you mentioned is the CE Smith Trailer Axle Beam #CE33201GA. This galvanized trailer axle has a spring center measurement of 46-1/2 inches and a hub face measurement of 57-1/2 inches.…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Parts To Rebuild Obsolete Hub For 3/4" Straight Spindle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching