Replacement Trailer Jack For a Trailstar Tracker 175 Boat Trailer

Question

Question:

Seems like a perfect replacement for my Trailstar Tracker 175 trailer! Your thoughts please.

asked by: William

0

Expert Reply:

The Swivel Marine Trailer Jack with Caster Wheel # DL67MR is a great replacement for the factory jack if you plan on using the caster on smooth surfaces. If you're using the jack to push the trailer around on rougher surfaces or dirt/grass the Xtreme Off-Road Swing-Up Trailer Jack # ORJW750D would be an upgrade. This uses dual wheels with rubber tires.

expert reply by: Bud M

0

Answer 1

We do carry the Fulton F2 Swing-Up Wide-Track Trailer Jack, part #F1413040134. This jack does come with the swivel mount attached and also includes the U-bolts to attach to trailer frames that measure either 3 inch by 3 inch or 3 inch by 4 inch. This…

view full answer...

Answer 2

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 3

Thank you for the measurements of your current bearing! Based on your measurements you need the Replacement Thrust Bearing for 5,000-lb Capacity Bulldog Jacks #BD500223 which has an Inner Diameter of .525", an Outer Diameter of 1.25", and a…

view full answer...

Answer 4

For a typical trailer wiring you will have a brown and green wire for the right-hand side of the trailer and brown and yellow wire for the left side. If this is a new wiring installation and you are installing wiring like part #A35W42B, the brown…

view full answer...

Answer 5

To pick out the best jack for your application you will definitely want to find out what the Tongue Weight (TW) of your trailer is when your boat is loaded on it. You can find this using a tongue weight scale like #e99044 or the method of using a…

view full answer...

Answer 6

Hi Tony; the #BK2-100 and #TMK52VR come with the same size bearings and grease seal. The main difference is the Timken name. This is usually associated with a higher quality bearings that are made in the USA which also accounts for the higher cost.

view full answer...

Answer 7

Hey Mike, it would be really odd if your other axle used a different bearing kit so I would feel very confident that if the one axle took the part #TMK52VR the other would too.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Trailer Jack For a Trailstar Tracker 175 Boat Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching