Recommended Replacement Thrust Bearing For 5000lb Trailer Jack

Question

Question:

Hello, Im looking for a 5,000 lbs trailer jack trust bearing. I see you have several but Im not sure which one I need. The dimensions of the product are: - inner diameter 25mm or 5/8 - outer diameter 32mm or 1 1/4 - height 7/16 Thank you

asked by: Michael T

0

Expert Reply:

Thank you for the measurements of your current bearing!

Based on your measurements you need the Replacement Thrust Bearing for 5,000-lb Capacity Bulldog Jacks # BD500223 which has an Inner Diameter of .525", an Outer Diameter of 1.25", and a thickness of .43".

I included a video of the Replacement Thrust Bearing # BD500223 for you to take a look at.

expert reply by: Samuel C

0

Answer 1

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 2

The Swivel Marine Trailer Jack with Caster Wheel #DL67MR is a great replacement for the factory jack if you plan on using the caster on smooth surfaces. If you're using the jack to push the trailer around on rougher surfaces or dirt/grass the…

view full answer...

Answer 3

Hey Mike, it would be really odd if your other axle used a different bearing kit so I would feel very confident that if the one axle took the part #TMK52VR the other would too.

view full answer...

Answer 4

Hi Tony; the #BK2-100 and #TMK52VR come with the same size bearings and grease seal. The main difference is the Timken name. This is usually associated with a higher quality bearings that are made in the USA which also accounts for the higher cost.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Recommended Replacement Thrust Bearing For 5000lb Trailer Jack

Featured Help Information

Miscellaneous Media

Continue Researching