Do You Offer The Buckle Separately From The Replacement Tie-Down for Extang Solid Fold 2.0?

Question

Question:

Do you sell just the buckle for the Extang Solid Fold 2.0 Hard Tonneau Cover replacement tie down?

asked by: Vernon

0

Expert Reply:

The Replacement Tie-Down for Extang Solid Fold 2.0 Hard Tonneau Covers # EX1024 is the only way we sell the buckle as that is the only way Extang offers these parts.

expert reply by: Bud M

0

Answer 1

Hi Clarence, I can see why you’re asking because a lot of these straps and buckles look like they should work until you go to clip them in and the fit is just a little off. I have what you need but the buckle and strap conversion kit part…

view full answer...

Answer 2

We do have the whole buckle assembly Replacement Tie-Down for Extang Solid Fold 2.0 Hard Tonneau Covers - Qty 1 #EX1024 If you need just the female end you want Tie-Down Buckle for Extang SolidFold 2.0 Tonneau Covers #EX54560402 available as just the…

view full answer...

Answer 3

Since you have the SolidFold 1.0 the correct buckle replacement is the part #EX1018 instead of what you have now.

view full answer...

Answer 4

The Replacement Tie-Down for Extang Solid Fold 2.0 Hard Tonneau Covers - Qty 1 #EX1024 is what you want for the Solid Fold 2.0. It includes the strap and male buckle, but not the female buckle. If you need that you will want the Replacement Female…

view full answer...

Answer 5

Based on your images it appears you have a BAKFlip Tonneau Cover. This will use the Buckle and Strap Conversion Kit #PARTS-356A0009. The Replacement Tie-Down #EX1024 you found is for Extang Solid Fold 2.0 Hard Tonneau Covers which are only 3 panels.

view full answer...

Answer 6

Thanks for the picture! Wthout knowing for sure what model tonneau cover you have, I can't say for sure. However, it does look like this strap will be compatible with your tonneau cover. As long as you have the 83-XXX series Extang Solid Fold 2.0…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Do You Offer The Buckle Separately From The Replacement Tie-Down for Extang Solid Fold 2.0?

Continue Researching