Replacement Female Buckle for Extang SolidFold 1.0 Tonneau

Question

Question:

Hi, I own the solid fold 1.0 and need replacement buckles. Is this something you can provide? I just bought a new set from etrailer and the buckle part doesnt mount flush to the front edge of the cover. Must be meant for the 2.0. Here is a link for what I need but again I have the 1.0, not the 2.0. EX54560402

asked by: Brandon H

0

Expert Reply:

Since you have the SolidFold 1.0 the correct buckle replacement is the part # EX1018 instead of what you have now.

expert reply by: Jameson C

0

Answer 1

Hi Clarence, I can see why you’re asking because a lot of these straps and buckles look like they should work until you go to clip them in and the fit is just a little off. I have what you need but the buckle and strap conversion kit part…

view full answer...

Answer 2

We do have the whole buckle assembly Replacement Tie-Down for Extang Solid Fold 2.0 Hard Tonneau Covers - Qty 1 #EX1024 If you need just the female end you want Tie-Down Buckle for Extang SolidFold 2.0 Tonneau Covers #EX54560402 available as just the…

view full answer...

Answer 3

The Replacement Tie-Down for Extang Solid Fold 2.0 Hard Tonneau Covers - Qty 1 #EX1024 is what you want for the Solid Fold 2.0. It includes the strap and male buckle, but not the female buckle. If you need that you will want the Replacement Female…

view full answer...

Answer 4

Thanks for the picture! Wthout knowing for sure what model tonneau cover you have, I can't say for sure. However, it does look like this strap will be compatible with your tonneau cover. As long as you have the 83-XXX series Extang Solid Fold 2.0…

view full answer...

Answer 5

Based on your images it appears you have a BAKFlip Tonneau Cover. This will use the Buckle and Strap Conversion Kit #PARTS-356A0009. The Replacement Tie-Down #EX1024 you found is for Extang Solid Fold 2.0 Hard Tonneau Covers which are only 3 panels.

view full answer...

Answer 6

The Replacement Tie-Down for Extang Solid Fold 2.0 Hard Tonneau Covers #EX1024 is the only way we sell the buckle as that is the only way Extang offers these parts.

view full answer...

Answer 7

The distance between the mounting holes of the Extang buckle part #EX54560402 that you referenced is 1-1/4 inches.

view full answer...

Answer 8

I reached out to my contact at Extang and the correct replacement female tie-down buckle for your original SolidFold Tonneau Cover is the part #EX1018. While similar in appearance the Tie-Down Buckle #EX54560402 that you referenced only fits the 2.0…

view full answer...

Answer 9

First you will need to determine if you have the Extang Solid Fold 1 or 2.0 on your 2014 Ford F-150, as the update occurred right at the same timeframe your F-150 was made. The best way to tell the difference is by the release handles on the tailgate…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Female Buckle for Extang SolidFold 1.0 Tonneau

Product Page this Question was Asked From

Continue Researching