Does Malone Bunk Kit MPG561 Fit Microsport Trailer

Question

Question:

I have the heavier 1.25” crossbars on my Malone Microsport trailer.Will the bunk set MPG561 fit on on the 1.25” Crossbars?

asked by: Bruce G

1

Helpful Expert Reply:

Yes, the Bunk Kit # MPG561 that you referenced will fit and work perfectly on the Malone MicroSport trailer as we have confirmed this with Malone in the past that it fits your trailer and it's crossbar size.

expert reply by: Jameson C

1

Answer 1

There really isn't an advantage to moving to a higher load range so I would choose the #AM30590 over the #AM30670 to save a little money. The tires are both made by Kenda and fairly comparable to each other with the same 5-year warranty.

view full answer...

Answer 2

Hey Jeff, great question but when you install the Malone Low Bed conversion kit #MAL33TR the crossbars will still be taller than the fenders like you can see in the attached picture. Are you wanting lower crossbars for easier loading/unloading?

view full answer...

Answer 3

To add bunk boards to the Malone MicroSport Trailer #MPG460G you'll want 2 of the Bunk Kit #MPG561 which actually installs on the crossbars. Since the Malone trailer frames are different you'll need to source U-Bolts to install the CE Smith…

view full answer...

Answer 4

I can certainly help with the dimensions of the U-bolts included with the #MPG561 Trailer Bunk Kit. The inside height of the leg is 2-1/4 inches measured from the end of the bolt to the inside of the top and the span measured inside leg to inside leg…

view full answer...

Answer 5

That's an excellent question, and you've got a good eye because the crossbars are about an inch lower than the fenders on the Malone 2 Tier LowBed MicroSport Trailer - 78" Crossbars #MPG464-LBT. So if you wanted to lay lumber completely…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Does Malone Bunk Kit MPG561 Fit Microsport Trailer

Product Page this Question was Asked From

Continue Researching