Dimensions of U-Bolts Included with Malone MPG561 Kayak Trailer Bunk Kit

Question

Question:

What is the dimensions of the u-bolt in this kit? In particular the inner gap.

asked by: Jason H

0

Expert Reply:

I can certainly help with the dimensions of the U-bolts included with the # MPG561 Trailer Bunk Kit. The inside height of the leg is 2-1/4 inches measured from the end of the bolt to the inside of the top and the span measured inside leg to inside leg is 1-1/4 inches.

expert reply by: Mike L

0

Answer 1

The Malone EcoLight Sport Trailers like item #MAL43FR have 8" tires with a 5 on 4-1/2 lug pattern. The Kenda 205/65-10 Bias Trailer Tire with 10" Galvanized Wheel item #AM3H490 would work as a replacement but you will most likely have to…

view full answer...

Answer 2

Hey Brian, we've had customer upgrade from the 4.80-8 tire size on the Malone EcoLight trailer part #MAL43FR to the next larger size of 5.70-8 like the part #AM10013. Is that what you were looking for? Or did you mean upgrade in a different way?

view full answer...

Answer 3

Hello Jeremy. The Malone Eco Light Trailer like part #MAL53FR comes with a 4.80/4.00-8" load range B trailer tire. If you are looking for an upgrade, I recommend the Kenda 4.80/4.00-8 Bias Trailer Tire with 8" Galvanized Wheel #AM30070.…

view full answer...

Answer 4

According to Malone, a heavier axle should not be installed on the EcoLight Sport Trailer #MAL53FR. Even if you did install a heavier axle, it would not increase the capacity of the trailer. You would still be limited to the 400 lb capacity due to…

view full answer...

Answer 5

Hey Ed, You can switch to larger tires but you would potentially need to move the fenders up to keep a minimum of 3" of clearance so that the wheels won't rub as the suspension compresses. Are you looking to just replace the tires and keep…

view full answer...

Answer 6

Since the Malone EcoLight trailer part #MAL53FR has a tongue width of 2 inches you could use the tower kit part #CE31013G which is 30 inches tall as this is designed to fit 2 inch channels. Then you could use a winch like the Buyers Products part…

view full answer...

Answer 7

Yes, you can add a winch to the Malone LowBed MicroSport Trailer item #MPG464-LB. You will want to use the CE Smith Winch Stand item #CE31013G. This will fit on the Malone trailer's 2" tongue. This stand is 30" tall and made of…

view full answer...

Answer 8

Chenchar, I recommend you upgrade your 8" tires on your Malone EcoLight Trailer #MAL43FR to a 10" wheel using the Kenda 205/65-10 Bias Trailer Tire with 10" Galvanized Wheel #AM3H490. These wheels are going to have the same bolt…

view full answer...

Answer 9

Since the Malone Microsport trailer part #MPG460G has a tongue width of 2 inches you could use the tower kit part #CE31013G which is 30 inches tall as this is designed to fit 2 inch channels. Then you could use a winch like the Buyers Products part…

view full answer...

Answer 10

There really isn't an advantage to moving to a higher load range so I would choose the #AM30590 over the #AM30670 to save a little money. The tires are both made by Kenda and fairly comparable to each other with the same 5-year warranty.

view full answer...

Answer 11

Hey Jeff, great question but when you install the Malone Low Bed conversion kit #MAL33TR the crossbars will still be taller than the fenders like you can see in the attached picture. Are you wanting lower crossbars for easier loading/unloading?

view full answer...

Answer 12

That's an excellent question, and you've got a good eye because the crossbars are about an inch lower than the fenders on the Malone 2 Tier LowBed MicroSport Trailer - 78" Crossbars #MPG464-LBT. So if you wanted to lay lumber completely…

view full answer...

Dimensions of U-Bolts Included with Malone MPG561 Kayak Trailer Bunk Kit

Product Page this Question was Asked From

Continue Researching