Trailer Hub With 4 on 4 Bolt Pattern & L44643 Bearings

Question

Question:

I am looking to replace the hubs on my TeeNee trailer. They are 4 x 4 bolt patern with L44643 bearings. The greases seal area is 1.25 BT8. My hubs are 3.625 length, do you have a simular length hub?

asked by: John L

0

Expert Reply:

Thank you for that detailed info it was super helpful and we do have hubs with a 4 on 4" bolt pattern that use # L44643 bearings. You can go with either a galvanized or non-galvanized option, whichever you prefer:

- Galvanized: Trailer Idler Hub Assembly # AKIHUB-440-2-G-1K

- Non-Galvanized: Trailer Idler Hub Assembly # AKIHUB-440-2-1K

These do include the bearings, races, and seal as well so you don't have to purchase anything separately.

expert reply by: Kyle S

0

Answer 1

BTR and BT8 are the reference numbers for a standard trailer spindle size. When picking out a hub for a trailer you have to make sure that the hub is designed to fit the spindle. What you will need to do is measure spindles on your trailer where the…

view full answer...

Answer 2

To find the correct hub for your boat trailer there are a couple things you need to know. First, you said the bearings you have are 07100. In my research I found that the 07100 bearing has an inner diameter of 1.000 inch. We have a bearing that…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Trailer Hub With 4 on 4 Bolt Pattern & L44643 Bearings

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching