Does the Curt Trailer Hitch C15409 Still Hang Down w/ out the Factory Hitch on a 2012 Ram 2500?

Question

Question:

If the option of no factory hitch installed is chosen. Does the curt hitch still hang low. 2012 Ram 2500

asked by: Mike

0

Expert Reply:

Yes, the Curt Trailer Hitch item # C15409 will still hang down even if you do not have the factory hitch installed. It looks like all of the aftermarket hitches for the 2012 Ram 2500 have the same profile.

The Curt Trailer Hitch item # C15409 is confirmed to fit your 2012 Ram 2500. It is made in the USA and has a 17,000 lbs towing capacity.

I have linked an installation video below.

expert reply by: Jerred H

0

Answer 1

Hello Michael. The Torklift Tie Down Set #TL82DR is what I recommend for your 2012 Ram 2500 long bed. This kit comes with both the front and rear tie downs. It is important to note that these tie downs are intended for trucks without steps or running…

view full answer...

Answer 2

The B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25211 is designed in a way that it will fit with or without a factory receiver. The multiple mounting points on the side plates will decide where the receiver sits. When you remove your factory…

view full answer...

Answer 3

All of our trailer hitches that fit your 2006 Dodge Ram 2500 with a factory hitch, will sit below the factory hitch. Since you are removing your factory hitch, the Curt hitch I recommend is #14361 as it's 6-1/2 inches from the top of the receiver…

view full answer...

Answer 4

The B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25211 we found hit a factory exhaust hanger on the short bed version of your 2005 Ram 1500. While this will fit with a simple relocation of the hanger we put the note saying it will only work on…

view full answer...

Answer 5

I would be happy to help you. Removing the factory hitch is not necessary and will be difficult to remove based on how it was attached to your Ram 2500's bumper. Ultimately, it'll be up to you but it being on there will have zero effect on…

view full answer...

Answer 6

When comparing the Draw-Tite Ultra Frame Trailer Hitch Receiver - Class IV, part #41929, to the Curt Trailer Hitch Receiver - Class IV, part #14361, they are similar, but the new version of the Draw-Tite #41929 is rated higher. The Draw-Tite Class IV…

view full answer...

Answer 7

The Curt Hitch part #14361 is designed to fit trucks without the factory hitch. I cannot recommend it for you since your factory hitch is built into the bumper beam which is built differently on the trucks with or without the factory hitch. It hangs…

view full answer...

Answer 8

Yes, your spare tire will be able to remain exactly where it is after you install the Draw-Tite Trailer Hitch Receiver #75420 on your 2004 Dodge Ram 1500. There is plenty of room for the hitch and spare tire to co-exist, as you can see in the…

view full answer...

Answer 9

view full answer...

Answer 10

Yes, the Curt trailer hitch #14361 is listed as a fit for all 2004 Dodge Ram 3500 series trucks. But it does not fit HemiSport Quad Cab, Ram Rumble Bee or SRT-10 models. I have included a link to the installation instructions for you. I also…

view full answer...

Answer 11

Thank you very much for your purchase directly from etrailer.com of your Reese brake controller. I'm not certain what the issue is but can offer you some troubleshooting steps. First, You will need to find out if the issue is on the brake…

view full answer...

Answer 12

You will need to hardwire the brake controller to your 2008 Dodge 1500. Because the wires have all been cut it would be best to run all new wires so you know it is done correctly. The four wires coming from the brake controller are White for ground.…

view full answer...

Does the Curt Trailer Hitch C15409 Still Hang Down w/ out the Factory Hitch on a 2012 Ram 2500?

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching