Do You Carry Replacement Keys For the Rod Vault From Denver Outfitters?

Question

Question:

I have an older Rod Vault by Denver Outfitters. The lock is stamped A2123. Will the replacement key on your site A21231 work? Thanks!

asked by: Napoleon

0

Expert Reply:

As you have the older Rod Vault from Denver Outfitters you will need the Replacement Latch and Keys # TH85ME. This is needed as the key alone will not work as a replacement for the Original Rod Vaults before they were acquired by Thule.

expert reply by: Bud M

0

Answer 1

Since you have an older model from before Thule acquired this fishing rod holder the only way to get a replacement key would be secondhand. You can however replace the entire lock assembly with the Replacement Locking Lever Latch and Keys for Thule…

view full answer...

Answer 2

The replacement key for your Thule Rod Vault #TH87YV will depend on the number that is found on the lock cores of your carrier. If the number on the face of the lock core is N090 then the #THKEYN090 will be the correct lock replacement. If you find a…

view full answer...

Answer 3

What brand equipment did the lock core come from, Thule or Yakima? A Thule lock has the lock number engraved onto the face of the lock, next to the key slot. The number will usually be preceded by the letter N. A Yakima lock has the number stamped…

view full answer...

Answer 4

You will need the Replacement Latch and Keys #TH85ME for the Thule Rod Vault #TH27YV, or #TH87YV. This will also fit the original Rod Vault which came from Denver Outfitters like you have. Thule does not carry any replacement keys for the units like…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hello Kevin, thanks for reaching out. Yakima does confirm the Timberline towers to fit the factory raised rails on the 2025 Honda Pilot. Sadly, they do not offer a direct fit for the LockNLoad Platform so your best option would be to go with a roof…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Do You Carry Replacement Keys For the Rod Vault From Denver Outfitters?

Product Page this Question was Asked From

Continue Researching