Self-Adjusting Trailer Brakes For a Lippert 4,400LB Axle On 2017 Aspen Trail 2790BHS Travel Trailer

Question

Question:

I have two lippert 4400 lb axles on my 17 aspen trail 2790bhs. I dont see brakes that fit lippert axles on your site, only dexter. Will 10 x 2.25 3500lb self adjusting brakes work?

asked by: Chris D

0

Expert Reply:

We do carry the Lippert Electric Trailer Brake Assemblies Left # LC96WD and Right # LC46WD from Lippert for their 4,400lb axles. These brakes are self-adjusting like the Electric Trailer Brake Kit # AKEBRK-35-SA.

expert reply by: Bud M

0

Answer 1

Hey Kevin, you would want 4,400 per axle and not 2,200 lb per axle. The closest we have for a leaf spring to that in 26 inch in length would be the part #e27SR which is for a 4,500 lb axle.

view full answer...

Answer 2

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Answer 3

There is not a designated location on a 5th wheel hitch like #RP30144 for the emergency Breakaway Kit #20099 cable. Most people will connect that cable to the tethered pin that locks the jaws of the head in place near the handle. You can see this at…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 10

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Self-Adjusting Trailer Brakes For a Lippert 4,400LB Axle On 2017 Aspen Trail 2790BHS Travel Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching