Recommended 15 Inch Black Wheel with 5 on 5 Inch Bolt Pattern

Question

Question:

I am looking for a black, 15 x 6, 5 on 5 bolt pattern, offset. Can you please give me the part number. Thanks

asked by: Lee R

0

Expert Reply:

The only 15" x 6" black trailer wheel with 5 on 5" bolt pattern that we offer is the Vesper Steel Modular Trailer Wheel part # TA97RR which has a 0 offset. Unfortunately, very few trailer wheels have an offset, none of which I could find in the color and size you need.

expert reply by: Conner L

0

Answer 1

We have just what you are looking for with the trailer hub part #AKIHUB-545-35-G-EZ-K. This has the correct bearing to fit your spindle and has the 5 on 4-1/2 inch bolt pattern you are looking for as well.

view full answer...

Answer 2

Hello Rob, thanks for reaching out. We do offer some 15x5 wheels with the 5 on 5 bolt pattern, but sadly we do not have anything galvanized. Our wheels should be either an acrylic enamel or powder coated. The 5 on 5 wheels are not super common these…

view full answer...

Answer 3

Hi Jason! A fancier 15" wheel with a 5 on 5 bolt pattern would be the Vesper Steel Modular Trailer Wheel - 15" x 5" Rim - 5 on 5 - Black #TA27RR. The 5 on 5 bolt pattern is getting less and less common these days, so the options are…

view full answer...

Answer 4

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Recommended 15 Inch Black Wheel with 5 on 5 Inch Bolt Pattern

Product Page this Question was Asked From

Continue Researching