Can You Trim Off Some Of The Lower Bend On The Stromberg Carlson RV Ladder To Fit A Motorhome Bumper
Updated 01/09/2023 | Published 01/06/2023
Question:
I do understand that the LA-401 ladder can be cut to the length that is required to fit my RV, but my question is more about the lower bottom Jinch section where it mounts to the RV. The curved end where it attaches to the RV would need to have approximately 2 inches cut off due to the RV molded bumper section that sticks out from the RV back wall by about 2 inches. So the out of the box 4 standoffs have a 5 inch standoff, but the Jinch section where it attaches to the RV would only be 3 inch standoff. See attached picture below where you can see the red circle of the area that would need to have approximately 2 inches cut off. I cannot raise the ladder higher because the taillights would be in the way. I can’t move the ladder to the right to the middle of the back wall, away from the taillights, because the vent on the roof would be in the way on the top section. Kind of stuck on mount it as in the pictures.
asked by: Warren B
Expert Reply:
You could cut off the two inches that you need from the lower bend on the # LA-401BA but you would need to find a way to crimp the end of the pipes to hold onto the mounting bracket. The ends of the pipes are simply rolled outwards to prevent the bracket from falling off. Most likely your local hardware store will carry some sort of pipe end shaping tool for you to accomplish this.
Product Page this Question was Asked From
Stromberg Carlson RV Exterior Ladder - Aluminum - 99-1/2" Tall - 250 lbs - Black
- RV Ladders
- Exterior Ladders
- Aluminum
- 8 Feet Tall
- Black
- Stromberg Carlson
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Troubleshooting Install of Redarc Tow Pro Elite That Doesn't Activate with Brake Pedal
- Shop: SmartPlug RV/Marine Data Port Inlet - Blank and Open Port - Gray
- Shop: SmartPlug RV/Marine Data Port Inlet - Blank and Open Port - Black
- Shop: etrailer Reversible RV Outdoor Rug w/ Stakes - 10' Long x 22' Wide - Charcoal and Gray
- Shop: Lippert Underchassis Double Bin Storage Unit for RVs - 99-1/2" Long
- Q&A: Does etrailer Carry Furrion Chill Cube w/ Heat Pump to Replace Dometic Duo-Therm
- Search Results: trailer tires and wheels
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Q&A: Best Suspension Upgrade for 33" Tandem Axles: Road Armor vs Dexter EZ Flex for Ember 22ETS
- Search Results: trailer hitch
- Shop: Power Mountain Tallboy Off-Road Bottle Jack - 8-1/2" to 37-3/4" Lift - 6 Tons
- Shop: Trailer Wiring
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer wiring
- Shop: Suspension Enhancement
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Video: A Look at the Power Mountain Tallboy 6 Ton Off-Road Bottle Jack with a Military Cargo Trailer
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Search Results: trailer jack
- Video: Feature Review - Big Truck Big RV Trailer Jack Foot Scale with Tongue Weight Gauge
- Shop: Brake Controller
- Article: 5 Things to Know About Weight Distribution Hitches
- Search Results: trailer lights
- Shop: Fifth Wheel Hitch
- Video: Replacement Dome Assembly for Ventline Ventadome Trailer Roof Vent Spec Review
- Q&A: Furrion Chill Cube Options for Travel Trailer
- Video: Towing Mirror Options - Custom Fit VS Universal Fit
on RV Ladders
