Replacement Brake Magnets For Dexter 10,000 lb Electric Brakes

Question

Question:

I have a 95 trailer with 10k axles the Model # D1012 I was wondering what size magnet’s are on these axles or do many work

asked by: Leon

0

Expert Reply:

The D1012 is a Dexter 10,000 lb axle, so it'll have 10,000 lb Dexter electric brakes like the Dexter Electric Trailer Brake Kit # 23-438-439.

Many do not work, as they do need specific brake magnets, and the correct replacement brake magnets for these brakes is the following:

- Replacement Magnet Kit for Dexter 12-1/4" Electric Brake Assembly # BP01-301

expert reply by: Kyle S

0

Answer 1

It's no secret that water and electricity do not do well together. That being said, improvements in wiring insulation and heat shrink connectors have made it more and more common for boat trailer manufacturers to use electric brake assemblies…

view full answer...

Answer 2

The Dexter Trailer Hub and Drum Assembly #DX68QR is for a single hub. These are not sold as pairs as they do not always have to be replaced as a set. We do offer the brakes for this either as a Set #23-438-439 or the Left #23-438 and Right #23-439…

view full answer...

Answer 3

Hey Juan! Depending on the jacks you may be able to add a motor like #LC196308 but you have to make sure it is rated for the weight up front (you're probably around 6,000 lbs but could be more). For a complete replacement I recommend the…

view full answer...

Answer 4

The spoke with Dexter and the code "D100G" tells me you have two 10,000 lb trailer axles. I have attached some parts you may need for the axle below. Dexter Trailer Hub Drum Assembly (After July 2009) - part #8-430-5UC3 Dexter Trailer Hub…

view full answer...

Answer 5

Unfortunately we do not carry any left hand threaded bolts, so, the closest we have to what you're needing would be the Dexter Brake Drum Mounting Screws #DX25KR - which have the same specs as the bolts you're looking for, but are right hand…

view full answer...

Answer 6

We do have the replacement screw and gear kit for your 12K Bulldog 180 Series Jack. You will need Gear Kit #BD500212 and Screw and Nut Kit #BD500217. You will also need grease for the new gears, so if you don't have any use #L11316. I included a…

view full answer...

Answer 7

The Bulldog Replacement Sidewind Gear Kit #BD500212 that you referenced is the correct repair kit for your Bulldog square tube jack according to my contact at Bulldog. The top cap you can use is part #BD017802. After you repair the jack you will want…

view full answer...

Answer 8

While we don't have replacement parts for a Model 70LP actuator, we do have a great replacement for it. Like the 70LP, these actuators are a fit for a 2" hitch ball, but they just have a slightly larger capacity at 7,500 lbs. You didn't…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Replacement Brake Magnets For Dexter 10,000 lb Electric Brakes

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching