How to Replace Yakima FrontLoader Knob

Question

Question:

seems front loader red knob is stripped ? seems to loosen some while driving. its a post 2016 rack. how do i remove and replace the knob ?

asked by: Lisa

0

Expert Reply:

To replace the knob on your Yakima FrontLoader # Y02103 you will remove the brass nut and bolt that keep the knob secure. If your FrontLoader was made after 2016 you need the # 8880766. If it was made before 2016 you will need the # 8880226 instead.

expert reply by: Robin H

0

Answer 1

There shouldn't be another washer on the Replacement Red Knob for Yakima Frontloader Fork Mount Bike Carrier #8880226. That appears to be part of the internal threads on the red knob itself. To replace this piece you'll just have to replace…

view full answer...

Answer 2

There are a few ways to tell if you have a pre-2016 or post-2016 Yakima FrontLoader Wheel Mount Bike Carrier part #Y02103. The best way to tell is to look for the date code sticker which is usually located near the front wheel holder. The easiest way…

view full answer...

Answer 3

Is it possible your FrontLoader was built after 2016 which would mean you'd need the knob part #8880766 which has a different nut in it and would explain why the older knob #8880266 isn't threading correctly.

view full answer...

Answer 4

Yes, you will remove the brass nut and bolt and the red knob will come off. You should note that the #8880226 does not come with a new nut (just a washer), so be sure not to lose your current one.

view full answer...

Answer 5

You will want part #8880766 , which includes the brass nut for the Yakima FrontLoader bike rack made after 2016. This includes the brass nut that secures the knob to the bike rack. If you have one made prior to 2016, you'll want part #8880226…

view full answer...

Answer 6

Hey James, so the difference between the two knobs is going to be when the rack you have was made. If your Frontloader was made after 2016 you need the part #8880766 or if before you'd need part #8880226.

view full answer...

Answer 7

It does sound like you may have overtightened or there is something wrong with the threading on your knob on your Yakima Frontloader. Replacing the knob should solve your problem. If you have Yakima FrontLoader bike rack made after 2016 you will need…

view full answer...

Answer 8

The Yakima Replacement Hitch Hardware for Yakima HoldUp Bike Racks #8890260 that you referenced is Metric.

view full answer...

Answer 9

The dynamic weight capacity of the RetraxPRO XR Hard Tonneau Cover #RTT-80851 is 500 lbs so it would easily handle the 600 lb weight you mentioned since that would be a "static" weight meaning it's not weight on the rack when on the…

view full answer...

Answer 10

The vast majority of rooftop mounted accessories nowadays work with all different kinds of crossbar shapes such as round, square, aero/elliptical and most factory crossbars. If you're having issues with the accessories moving when used with round…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

How to Replace Yakima FrontLoader Knob

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching