Solution for Needing Replacement Cap of Kodiak XL ProLube Kit XLPROLUBE1980KIT

Question

Question:

Kodiak XL ProLube Kit for 3500-lb Axles Item # XLPROLUBE1980KIT I just need the blue cap.

asked by: Patrick D

0

Expert Reply:

I have a solution for you but just the blue cap of the Kodiak XL ProLube Kit for 3500-lb Axles Item # XLPROLUBE1980KIT that you referenced is not available. So your best option would be the Kodiak XL ProLube Oil Bath Hub Body and Cap # xlprolube1980 which is the blue cap and the metal piece it attaches to.

expert reply by: Jameson C

0

Answer 1

Hey Chris! We don't have the O-rings individually but we do have the Kodiak XL ProLube Oil Bath Hub Body and Cap - 1.98" #xlprolube1980. These are the same caps that came with your disc brakes. If you need anything else feel free to reach…

view full answer...

Answer 2

In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information. The first thing you will need to know is the bolt pattern of your hubs. This is so you get a hub that is compatible with your…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 10

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 11

Hey Jascha, yes you can easily change the Kodiak disc brake kit part #KOD53FR to being an oil bath setup by just swapping out the seal to the part #9103309. What's really interesting about the part #KOD53FR is that it actually has oil bath type…

view full answer...

Solution for Needing Replacement Cap of Kodiak XL ProLube Kit XLPROLUBE1980KIT

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching