FM Antenna Recommendation for 2003 Airstream International 22 CCD

Question

Question:

I need a new rooftop FM radio antennae for my 2003 Airstream International 22’ CCD. Can you tell me which one will work for my camper? Thanks,

asked by: Andy N

0

Expert Reply:

The Jensen FM antenna part # AN519 would be a great option for the roof of your 2003 Airstream International. The cable that comes with it is 180 inches long and the mast is 31 inches which means it will be plenty long to install on your RV and provide great reception which is what our customers who have it have reported.

expert reply by: Jameson C

0

Answer 1

Hey Steven, thanks for reaching out. We should have a stereo option for you, but there isn't a way to look up your camper to know exactly which stereo it was equipped with from the factory. Basically, we'll just want to be sure the new unit…

view full answer...

Answer 2

Hi Phil! The main difference between the etrailer Easy Grease Trailer Hub and Drum Assembly #AKHD-865-7-2-EZ-K and the Dexter Trailer Hub and Drum Assembly #42866UC3-EZ is where they are made. Ours are made over seas and Dexter hubs are made here in…

view full answer...

Answer 3

The P-15 model information you provided for your Dexter axle does indicate its model, but you will still need to note its length and capacity before locating the correct replacement. If you are able to find a longer serial number somewhere on the…

view full answer...

Answer 4

I spoke with Furrion, and they told me that the antenna with the Furrion 4G LTE WiFi Router and Rooftop Antenna for RV's #FR57FR will reach up to approximately 400 ft.

view full answer...

Answer 5

Really it depends on which axle is carrying more of the weight. Typically the front axle is the braking axle for most utility trailer and campers but for boat trailers where the weight is more on the back it's typically the rear axle. We have…

view full answer...

Answer 6

Hello Daniel, thanks for reaching out. We do have the drums, brakes and bearings for the 7K torsion axles. Here is what I recommend: - Easy Grease Trailer Hub and Drum Assembly for 5.2K - 7K Axles - 12" - 8 on 6.5 - Pre-Greased…

view full answer...

Answer 7

Hey Grae; that doesn't seem to be a complete serial number so I won't be able to identify it with that information. I would pull the existing hubs and see if the bearing numbers are stamped into the sides of the bearings to try and identify…

view full answer...

Answer 8

The etrailer.com Electric Trailer Brake Kit #AKEBRK-7-SA and the Dexter Nev-R-Adjust Electric Brake Kit # 23-464-465 referenced in your question are both self-adjusting assemblies that will work to replace the existing Dexter brakes on your 7,000…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

FM Antenna Recommendation for 2003 Airstream International 22 CCD

Continue Researching