Can Curt CrossWing LightWeight Fifth Wheel be Used with Cushioned Pin Box on Trailer

Question

Question:

Can the Kurt crosswing be used with trailer air hitch with air bags?

asked by: Mark

1

Helpful Expert Reply:

Yes, the Curt CrossWing Lightweight 5th Wheel Trailer Hitch # C86JR that you referenced can be used with fifth wheel trailers that have cushioned pin boxes.

expert reply by: Jameson C

1

Answer 1

Sergio, yes, the PullRite SuperGlide part #PUL63RR will work with your MORryde cushioned pin box like part #MR55QR. you will just need to pair it with the PullRite SuperGlide Quick Connect Capture Plate part #PUL76RR for the setup to function…

view full answer...

Answer 2

Hey Jerry, thanks for reaching out. It sounds like you are needing the Replacement Stability Disc Kit for MORryde Rubber Pin Box #MR26RV. We will be getting more of these in stock. Right now we are expecting them to be available to ship in 4-5…

view full answer...

Answer 3

Hey Matt, I was able to track down a set of install instructions for the PullRite SuperGlide Quick Connect Capture Plate for MORryde Cushioned Pin Boxes #PUL76RR that I saw you ordered in your order notes. I attached the pictures below this message…

view full answer...

Answer 4

Yes, the Curt Crosswing fifth wheel hitch part #C86JR is compatible with the cushioned MORryde pin boxes but you also have to use the #MR37ZR. The only MORryde pin box it's not compatible with is the pivoting Orbital pin box.

view full answer...

Answer 5

The reason you'd need the 5th-Wheel-to-Gooseneck Coupler Adapter Mounting Plate for MORryde Pin Boxes #MR37ZR is because in order to use a 5th wheel to gooseneck adapter like the Ranch Hitch Universal 5th-Wheel-to-Gooseneck Coupler Adapter…

view full answer...

Answer 6

Hey Darrel, that would be pretty cool but we don't have a lock for the upper section of the Curt Crosswing hitch part #C86JR.

view full answer...

Answer 7

Hey Kevin, you are correct and thank you for bringing this to our attention. To use the Curt CrossWing part #C86JR you do need to use the MORryde Coupler Adapter part #MR37ZR as well. This is our part number for the RPB77-006. I also checked and…

view full answer...

Answer 8

If you are measuring for clearance on your Grand Design 28G Momentum for the install of the SumoSprings kit part #SS26MV you'd need to measure with the weight of the trailer on the ground. I wouldn't go so far as to load the trailer down as…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Can Curt CrossWing LightWeight Fifth Wheel be Used with Cushioned Pin Box on Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching