2007 Ford E450 Super Duty Brake Controller and Install Harness

Question

Question:

I cannot type in my vehicle in your -down box, not listed - Ford E450 or any E Series Ford trucks, only F series. Question: I believe I found the factory brake controller connector in my 2007 E450, can you tell me if this is the right connector? Please see photos. Ive been looking at your brake controllers, and tend to lean toward the Tekonsha proportional ones. Can you make a suggestion? Also the correct adapter cable for it? Thanks so much,

asked by: Linda B

1

Helpful Expert Reply:

Thanks for the picture and info on your Ford E-450. Based on that I can tell that the correct brake controller install harness would be the part # 3035-P for a Tekonsha brake controller like the Prodigy P3 part # 90195 which is widely considered to be the best brake controller out there due to how well it performs and how reliable it is.

expert reply by: Jameson C

1

Brake Controller Install Port
(click to enlarge)

Answer 1

If the Ford E-450 cutaway chassis your Class C is built on has a factory 7-way trailer connector it should also have a connection port for a trailer brake controller. You should find this behind the small dash panel shown in the linked photo. The…

view full answer...

Answer 2

I recommend the Bauer Products Camper Door Lock - Black #BA54FR. I feel they are a good quality brand and easy to operate. You can get them keyed alike by using the drop down menu before you add them to your cart. This particular version requires a…

view full answer...

Answer 3

I have attached an image of the Draw-Tite Ultra Frame Trailer Hitch Receiver #41947 referenced in your question with a few dimensions labeled. The distance between mounting holes, from the left side mounting bracket to the right side mounting bracket…

view full answer...

Answer 4

For the weight capacity and ease of installation, I recommend the Draw-Tite Ultra Frame Trailer Hitch Receiver - Class V #41947. This hitch is a confirmed fit for your vehicle. For your wiring harness, I recommend the 4-Pole Hardwire Kit with Circuit…

view full answer...

Answer 5

One of the Camco Premium Locking Wheel Stops #CAM44662 will effectively prevent the trailer from rolling. But adding a second one on the other side of the axles will further stabilize the trailer and help to reduce any wander from half the axle being…

view full answer...

Answer 6

Using two of the chocks is recommended (in fact, part #UF21-001070 includes two of them.) The Chock and Lock stabilizers brace your tandem wheels against one another, stabilizing your trailer even on unlevel terrain. No more front-to-back motion.…

view full answer...

Answer 7

The 2 inch spacing you have between the front and rear tires is enough to use Ultra-Fab chock #UF21-001060. It will fit tire spacing of 1-1/2 to 5-1/4 inches. I have included a link to a video review for you. For a set of 2 use #UF21-001070. You can…

view full answer...

Answer 8

There isn't an exact degree limit for wheel chocks like the #288-02011 to be considered safe or not. It's a situation where you'd need to use your best judgment and as long as the chocks don't appear to be failing you are going to be…

view full answer...

Answer 9

If you were to order Ultra-Fab wheel chock #UF21-001060, you would receive 1 wheel chock. For a pair you can use part #UF21-001070. Having 2 will provide extra protection but using 1 is usually enough depending on your intended application. These…

view full answer...

Answer 10

The Ultra-Fab Chock and Lock Wheel Stabilizers for Tandem-Axle Trailers and RVs part #UF21-001070 are good for stabilizing the fifth wheel with back and forth movement. Since your fifth wheel is on an incline I recommend to still use wheel chocks…

view full answer...

Answer 11

The B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25122 that will fit your 1986 Chevy K20 will measure 5.438" from the top of the frame brackets to the top of the receiver. If this is looking like it will not be enough to clear the bottom of…

view full answer...

Answer 12

On B&W trailer hitch #BWHDRH25122 the mounting brackets are oriented the same for all applications. The tabs point in but attach to the bottoms of the frame rails. The customer submitting photo appears to have some other component installed. The…

view full answer...

2007 Ford E450 Super Duty Brake Controller and Install Harness

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching