How Would Prodigy P2 Brake Controller Install in 2010 Toyota Tundra

Question

Question:

I have a 2010 Toyota Tundra. i need a brake controller. Im looking at the Tekonsha #90885. Would this be a good controller for a two axle trailer? Do all Tundras have a plug in for a controller? Where would I look/ What harness would I use? I also need a replacement female plug in in the rear. Maybe a 20135? Any other suggestions?

asked by: Michael T

0

Expert Reply:

Since your 2010 Toyota Tundra has a 7-way you do have the brake controller install port under the dash which means to install the P2 part # 90885 you'd just need the install harness part # 3040-P. The port is under the dash by the emergency brake pedal. You can see it in the attached install video for the P2 on a similar 2010 Tundra.

The P2 is a really nice brake controller that works well, is very reliable, and installs easily so we recommend it highly.

Then for a replacement 7-way you'd just need the part # PK11893 and you'd be set.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

Hey Dale, thanks for reaching out. For your 2010 Toyota Tundra with the factory tow package, a proportional controller is definitely the way to go for smooth braking on a 2-axle trailer, and a really clean option is the Redarc Tow-Pro Liberty…

view full answer...

Answer 12

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

How Would Prodigy P2 Brake Controller Install in 2010 Toyota Tundra

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching