Bolt Hole Pattern of Replacement Mounting Bracket for Kodiak Disc Brake Caliper # KCMB10RD

Question

Question:

I need the dimension of the location and hole size of these brackets

asked by: Allen P

1

Helpful Expert Reply:

I attached a picture that has all of the mounting hole dimensions of the Kodiak Disc Brake Bracket # KCMB10RD.

expert reply by: Jameson C

1

Bolt Hole Dimensions
(click to enlarge)

Answer 1

Yes we do. The calipers and brackets for the Kodiak Disc Brake Kit item #K2R35D can be purchased separately. The caliper is item #KDBC225DAC and the brackets are item #KCMB10RD. I have linked a diagram of the bracket for the Kodiak Disc Brake Kit…

view full answer...

Answer 2

Thanks for the pictures! You're correct, the Replacement Mounting Bracket for Kodiak Disc Brake Caliper #KCMB10RD is the correct replacement mounting brackets for your Kodiak 225 brake calipers. Attached is a product overview video for you to…

view full answer...

Answer 3

Steve, we do have kits like the DeeMaxx Disc Brake Kit #DE22FR which could potentially work with your 2023 Winnebago Hike. This brake kit will work with axles that have a 6K capacity, a 6 on 5 1/2 bolt pattern, and a 5 bolt brake flange configuration…

view full answer...

Answer 4

The only way you're getting a 12" wheel like #AM20153 on there is if you have a 2,000 lb axle and an 8" hub/rotor like the #KOD27FR. More than likely you have a 10" hub/rotor with a 3,500 lb axle. If that is the case, it will still…

view full answer...

Answer 5

I can certainty provide you with the information you need to select these parts yourself but as far as giving you a list of parts, that's not going to happen unfortunately as there are no resources available to look this stuff up. That said, to…

view full answer...

Answer 6

Hey Gerald, so we have the Kodiak disc brake kit part #KOD67FR which comes with the 10 inch hub/rotors, calipers, and brake mounting flanges as well as the bearings and seal but we don't have this kit with the brake lines. So you would need to…

view full answer...

Answer 7

Hello Rob, good question. The difference between the Caliper Brackets #KCMB10RD and #KCMB10HRD is the type of hubs they are intended to work with. The #KCMB10RD should be used with calipers on disc brake assemblies with over-the-hub rotors like part…

view full answer...

Answer 8

The Kodiak 225 calipers #KDBC225S fit 3,500 lb 10 inch assemblies as well as 12 inch rotors up to 5,200 lbs. The 204 calipers fit 3,500 lb axles with 10 inch assemblies. The 225 calipers are more prominent than the 204 calipers but they are not…

view full answer...

Answer 9

Thank you for providing that information. That is an EZ Loader custom trailer that uses #L68149 inner and #L44649 outer bearings. If you're looking for a hub/rotor assembly you can use the #KOD87FR as a replacement. If you already have an idler…

view full answer...

Answer 10

Hey Sam. The 1/2" diameter x 2" long studs on the Kodiak Trailer Hub for 3,500-lb Axles item #KH84545S are the same size as the rest of our options for hubs. These idler hubs are specifically designed to work with brake rotors like the…

view full answer...

Answer 11

There is a replacement that I recommend for the Tie Down 70E disc brake actuator, though you will want to verify that your mounting bolt holes are 3 inches apart on center and your tongue is a 3 inch channel. If they are I recommend the Dexter DX7.5…

view full answer...

Answer 12

I spoke with my contact at Kodiak. He stated that the UA code at the end of your existing caliper mounting bracket means that it is for a slip over (over the hub) or stainless steel rotor. We have 2 that fit this category, each with a different…

view full answer...

Bolt Hole Pattern of Replacement Mounting Bracket for Kodiak Disc Brake Caliper # KCMB10RD

Product Page this Question was Asked From

Continue Researching