Replacement Brake Assemblies For a Big Tex 22GN Trailer with 10K Dexter Axles

Question

Question:

Will this product replace the Dexter brakes on a BigTex 22GN with 10K Axles?

asked by: Kevin

0

Expert Reply:

Yes, the Electric Trailer Brake Kit # AKEBRK-10 can be used to replace the Dexter Electric Brake Kit # 23-450-451 that comes on a Dexter 10K axle. If you are needing any bearings or grease seals for this axle on your Big Tex Trailer I can confirm the parts used if you can provide me with the serial number found on your axle.

expert reply by: Bud M

0

Answer 1

We don't have any locks that would work with that coupler, do you see a brand or any info on it? With that info it might be possible to find a lock that would work for it. Otherwise you could use a wheel lock like the part #288-02020 which would…

view full answer...

Answer 2

The Ram Gooseneck to 5th Wheel Trailer Coupler Adapter Inner Tube - Square - 30,000 lbs #KPG5-Q30IP is a 4 inch square tube with a 7/8 inch pin hole diameter. The holes are 2-11/16 inches on center and have a total adjustment height of 8 inches. The…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Replacement Brake Assemblies For a Big Tex 22GN Trailer with 10K Dexter Axles

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching