Bearing Buddy that Could Fit Hub Bore of 2.1 inch

Question

Question:

Trying to find a bearing buddy to fit an older trailer. The inside dimension of the hub is 2.1 in, 53.72 mm, or 2 15/128.

asked by: Bill B

1

Helpful Expert Reply:

The Bearing Buddy closest to that would be the part # BB2080 which is designed for a hub bore that is 2.08 inches. Is it possible you were off by .02 of an inch.

expert reply by: Jameson C

1

Answer 1

The measurements you gave aren't quite enough because you have to measure the spindle down to the thousandths of an inch. So you need to use a digital caliper and measure your spindle at the places in the diagram you say (which I also posted for…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 4

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 12

Hey Charles, Yep, the Demco Autoslide 5th Wheel Trailer Hitch for Chevy/GMC - Single Jaw - Underbed #DM36SV is a kit that includes the Underbed Rail and Installation Kit #DM8551004 and the Demco Autoslide 5th Wheel Trailer Hitch #DM8550022. The…

view full answer...

Bearing Buddy that Could Fit Hub Bore of 2.1 inch

Product Page this Question was Asked From

Continue Researching