How to Determine if Dexter Tandem-Axle Trailer Hanger Kit for 2-1/2 Slipper Springs Will Work

Question

Question:

I had a chance to measure the springs and they are 3” wide. Do you have a kit that will work?

asked by: Gerald A

0

Expert Reply:

I can tell you how to determine that, but there isn't a specific fit for any trailer, including your Big Tex, for the Dexter Tandem-Axle Trailer Hanger Kit for 2-1/2" Slipper Springs # HAP-158-258-03.

Since you have 10,000 lb Dexter axles, you're set there, and you likely have 2-1/2 inch slipper springs (though you may want to measure their width just to be sure), so all you have to do is measure you axle spacing. To do this, simply measure from the center of one axle to the center of your other axle.

If that measurement is 48-1/2 inches you can use the Dexter Tandem-Axle Trailer Hanger Kit # HAP-158-258-03.

expert reply by: Kyle S

0

Jerry A.

8/15/2022

I had a chance to measure the springs and they are 3” wide. Do you have a kit that will work?

Kyle S.

8/15/2022

Thanks for that info and yes, we do have 3" wide slipper spring kits, and here are your options, depending on your axle spacing: - 38" Axle Spacing: Dexter Tandem-Axle Trailer Hanger Kit for 3" Slipper Springs # HAP-103-203-01 - 42-1/4" Axle Spacing: Dexter Tandem-Axle Trailer Hanger Kit for 3" Slipper Springs # HAP-103-203-02 - 48-1/2" Axle Spacing: Dexter Tandem-Axle Trailer Hanger Kit for 3" Slipper Springs # HAP-103-203-03

Answer 1

For your trailer, the axle placement will dictate the hanger placement as will whether you use double eye springs or slipper springs. When positioning a trailer axle or adding an additional axle, the key is to make sure that the axles are located in…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

How to Determine if Dexter Tandem-Axle Trailer Hanger Kit for 2-1/2 Slipper Springs Will Work

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching