Replacement Lens for 7-3/4 x 3-1/4 Inch Optronics Trailer Tail Light

Question

Question:

Optronics lens cover - L = 7 3/4 H = 3 1/8 D = 2 1/4 Do you carry? Cant find part number

asked by: Brian G

0

Expert Reply:

Based on the dimensions you provided, you're most likely looking for the Optronics replacement lens # A39RB, which fits the Optronics Aero Pro Trailer Tail Light Drivers Side item # ST37RB or the Passenger Side item # STL36RB and measure 7-7/8" long x 3-1/4" tall. This is the closest match to the dimensions you provided.

expert reply by: Jerred H

0

Answer 1

The dimensions of the Replacement Tail Light Lens for ST36RB and ST37RB, item #A39RB, are 7-7/8 inches Long x 3-1/4 inches Wide. This lens is designed to fit the Over 80 inch, Aero Pro Submersible Trailer Tail Lights, item #ST36RB and #ST37RB.

view full answer...

Answer 2

The SAE STIAP2 04 DOT number you provided is a DOT approval number, which states that the lens is compliant with DOT regulations. Because of that, that number isn't typically a good identifier for finding a replacement lens. However, in this…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Lens for 7-3/4 x 3-1/4 Inch Optronics Trailer Tail Light

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching