Is Fulton XLT Trailer Jack F26ZR A Bolt On or Bolt Through Jack

Question

Question:

Hi - I’m looking at getting a Fulton trailer jack, part F26ZR, and wanted to make sure it is a bolt THRU mount as the description says bolt thru and bolt mount and I can’t tell from the photos. Thank you.

asked by: Phil K

0

Expert Reply:

The Fulton XLT Bolt-Thru Swivel Trailer Jack # F26ZR comes with brackets that would allow you to attach to the trailer frame that bolt around the frame but if you wanted to drill holes in the trailer frame and attach it through the frame you could do that as well.

expert reply by: Jameson C

0

Answer 1

If you are not wanting a bolt-on jack such as the Fulton XLT Bolt-Thru Swivel Trailer Jack, #F26ZR we have the Fulton F2 Adjustable A-Frame Jack, #F1413250334. The F2 Series jack is specially designed for use with Fulton's F2 A-frame coupler. If…

view full answer...

Answer 2

The mounting plate for the Fulton XLT Bolt-Thru Swivel Trailer Jack #F26ZR has the following dimensions. I have included an image to show the measuring points. The holes are spread 5-1/2" wide with the vertical holes separated 1" on the…

view full answer...

Answer 3

We have a great option for a boat trailer jack that is going to easily swivel with the Fulton XLT jack. Keeping in mind that all jack wheels can struggle turning if there is too much weight on them, the XLT has a very high-quality caster and wheel…

view full answer...

Answer 4

The Lend-a-Hand Extra Large Folding Grab Handle for RVs - Black with Black Foam Grip - Aluminum #AM-533 have brackets that have three holes in each. I went out to our warehouse to measure for you and the holes from top bracket to bottom bracket are…

view full answer...

Answer 5

You referenced the Camco Fold-Away RV Grab Handle #CAM42176 but I am not sure that is what you have in your picture as the mounting brackets aren't supposed to have those indentions. There is actually a spring on the Camco part you mentioned that…

view full answer...

Answer 6

There is no weight rating for the Mounting Bracket, part #TV-0002. It is designed to replace the bracket for the Trailer Valet Trailer Jack, part #STC-V211. The Trailer valet has a weight capacity of 500 lbs. You may be able to install a different…

view full answer...

Answer 7

In regards to the Fulton XLT Bolt-Thru Swivel Trailer Jack part #F26ZR, the distance from the center of the mounting bracket to the top of the jack tube cap is 13.4". I have attached a photo below as well to show this. I spoke to Fulton and this…

view full answer...

Answer 8

I went ahead and checked out your Fulton XLT Bolt-Thru Swivel Trailer Jack #F26ZR, and the Fulton F2 Swing-Up Trailer Jack, and you actually won't be able to use this mounting bracket with your XLT jack due to the fact that the plate for the F2…

view full answer...

Answer 9

Though we do not carry a complete replacement wheel assembly for the Fulton XLT Bolt-Thru Swivel Trailer Jack #F26ZR, you will have to purchase the entire jack again. If you have any further questions please feel free to reach back out to me anytime…

view full answer...

Answer 10

Yes, since your current Fulton jack is a bolt-thru style, you can use the Fulton XLT Bolt-Thru Swivel Trailer Jack #F26ZR with your current welded on bracket. You just need to remove the jack from the included bolt-on bracket and mount it to your…

view full answer...

Answer 11

If you used a 1.5 inch spacer to make your 1.5 inch wide frame 3 inches wide you could use the Fulton XLT Bolt-Thru Swivel Trailer Jack #F26ZR.

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Is Fulton XLT Trailer Jack F26ZR A Bolt On or Bolt Through Jack

Product Page this Question was Asked From

Continue Researching