How Tight Should Spindle Nut of Timbren Axle Less Kit be

Question

Question:

Hi there. What size socket is required for the Timbren Axle-Less Trailer Suspension System - 4inch Lift Spindle w/ Brake Flange? Thanks

asked by: David L

0

Expert Reply:

When installing spindle nuts like what comes on the Timbren Axle Less Kit # TASR5200S03 Timbren recommends tightening the nut to 50 ft lbs and then backing off 1/8 turn.

expert reply by: Jameson C

0

Answer 1

To initially adjust the brakes, you will need to raise the trailer and secure it on adequate capacity jack stands. Check that the wheel and drum rotate freely. Do not lift or support trailer on any part of the axle or the suspension system. Remove…

view full answer...

Answer 2

Converting from manual adjust to self-adjusting brakes is as simple just replacing the assemblies. The self-adjusting portion of the assemblies is all self-contained and takes care of itself. The assemblies install in the exact same way too. The part…

view full answer...

Answer 3

Hey Matt! Thanks for confirming that information below. The Timbren Axle-Less Trailer Suspension - Heavy Duty - Long Spindle w/ 4" Lift #ASR1THDS03 uses a #84 spindle so you will need 3,500 lb hubs to match. If you want an idler hub you can use…

view full answer...

Answer 4

The Double Lip Grease Seal part #58846 is indeed the correct replacement for a GS1719 Grease Seal.

view full answer...

Answer 5

There are really two reasons to replace a grease seal, if they are damaged or worn and leaking grease then that is an obvious factor. If you are replacing bearings it is usually best to replace the grease seals as well because although they may still…

view full answer...

Answer 6

Hey Dave, yes the Timken grease seal part #TMK58ZR is a replacement for what you have now. I would go with the Timken but we also do carry your exact part number replacement with the part #58846.

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

How Tight Should Spindle Nut of Timbren Axle Less Kit be

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching