Ventline Model V2394 Operator and Crank Handle Replacement

Question

Question:

Need a replacement operator with crank handle for a ventline model V2394. What part/model number would that be? thanks

asked by: Rod

0

Expert Reply:

For a Ventline V2394 roof vent the correct replacement operator with crank handle is the part # BVD0462-00.

expert reply by: Jameson C

0

Answer 1

I recommend using the MaxxAir II RV and Trailer Roof Vent Cover #MA76JR as it is easily removable allowing you to easily clean under the cover and check the sealant. If you are only needing a lid you will need either the Pre-2008 #BV0554-01 lid or…

view full answer...

Answer 2

I'm not sure which parts of the vent assembly you need for your Ventline Model V2394, but we do carry a bunch of replacement parts for it. For a replacement operator knob and screw, you can use the Replacement Operator, Knob and Screw for…

view full answer...

Answer 3

For your older Ventline 2394, you can use the Replacement Operator, Knob and Screw for Ventline Ventadome Trailer Roof Vents w/ Wedge-Shaped Dome #BVD0462-00. This kit includes the operator, knob, and mounting screw and is made in the USA. Attached…

view full answer...

Answer 4

The Stromberg Ladder part #LA-401 is a universal ladder designed to fit as many RVs as possible. If Lance says that you can only install one of their ladders I wouldn't recommend you go against that recommendation as it could void warranties. I…

view full answer...

Answer 5

I've confirmed with Ventline that the #BVD0434-31 screen is the correct replacement screen for the VD0434 roof vent in your truck camper.

view full answer...

Answer 6

To determine which replacement lid you need you will need to check the hinge on the roof of your vent lid. I have included an chart that has the most common lids and shows the hinges. Once you identify the hinge you will need one of the following…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Ventline Model V2394 Operator and Crank Handle Replacement

Product Page this Question was Asked From

Continue Researching