Replacement Arm Mechanism For an Older Ventline V2394

Question

Question:

I have a ventline model 2394 and need a replacement mechanism arm for it, what model part do i need

asked by: Aarron W

0

Expert Reply:

For your older Ventline 2394, you can use the Replacement Operator, Knob and Screw for Ventline Ventadome Trailer Roof Vents w/ Wedge-Shaped Dome # BVD0462-00.

This kit includes the operator, knob, and mounting screw and is made in the USA. Attached is a product oveview video for you to check out as well.

expert reply by: Bryce D

0

Answer 1

For a Ventline V2394 roof vent the correct replacement operator with crank handle is the part #BVD0462-00.

view full answer...

Answer 2

I'm not sure which parts of the vent assembly you need for your Ventline Model V2394, but we do carry a bunch of replacement parts for it. For a replacement operator knob and screw, you can use the Replacement Operator, Knob and Screw for…

view full answer...

Answer 3

I recommend using the MaxxAir II RV and Trailer Roof Vent Cover #MA76JR as it is easily removable allowing you to easily clean under the cover and check the sealant. If you are only needing a lid you will need either the Pre-2008 #BV0554-01 lid or…

view full answer...

Answer 4

I've confirmed with Ventline that the #BVD0434-31 screen is the correct replacement screen for the VD0434 roof vent in your truck camper.

view full answer...

Answer 5

The Stromberg Ladder part #LA-401 is a universal ladder designed to fit as many RVs as possible. If Lance says that you can only install one of their ladders I wouldn't recommend you go against that recommendation as it could void warranties. I…

view full answer...

Answer 6

To determine which replacement lid you need you will need to check the hinge on the roof of your vent lid. I have included an chart that has the most common lids and shows the hinges. Once you identify the hinge you will need one of the following…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Arm Mechanism For an Older Ventline V2394

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching