Mounting Brackets for Fulton Trailer Fenders # F008592

Question

Question:

Mounting brackets for 12 inch fenders. I can’t seem to find the brackets for the Fulton plastic fenders thanks

asked by: Jason

0

Expert Reply:

The Fulton trailer fender part # F008592 that you referenced was designed to be used with brackets # PF1135-BKT-2.

expert reply by: Jameson C

0

Answer 1

The M1 measurement on Fulton fender #F008592 is 22.7 inches which is less than 5/16 inches shorter than your 23 inch measurement. Basically, your fenders could have spread out a little over time or if they get warm and pliable so they could have…

view full answer...

Answer 2

Your best bet would be an underbody tool box like the part #UB1818-48 if you can find a place to put it on your trailer to allow you to store your jack and wheel wrench. While this is intended to be installed on the underside of your trailer you…

view full answer...

Answer 3

I can help you determine if the Fulton fenders you asked about fit your trailer, but fenders are universal parts and there is simply no way to know what fits any specific year, make and model of trailer (this is actually true for all trailer parts…

view full answer...

Answer 4

For 13 inch trailer wheels we have the Single Axle Trailer Fender with Backing part #HP79VR which would be a great option. Here are the dimensions for you to compare to your trailer. 7-3/4" Wide x 28" long x 10" tall.

view full answer...

Answer 5

Based on your measurement and image it appears you will need the Fulton Single Axle Trailer Fenders with Top and Side Steps which we have in Black #F008584-2 or Silver #F008594-2. These fenders separate the side mounting holes 30-1/4" from front…

view full answer...

Answer 6

The only white fenders we have that will fit your 15" wheels are the #PF11X35W-2. We also have reports that this was a match for a 2000 Escort boat trailer, so it is likely this is the same part. If you decide you only want to place the one…

view full answer...

Answer 7

Your typical 4.80-12 tire like #AM10062 has an outer diameter of 20.5" and section width of 4.8". Since you currently have 3.5" of clearance on top, and 3" is the minimum, you can only move up 1" in tire diameter. This means…

view full answer...

Answer 8

Hello JT, At this time we do not have mounting brackets that bolt up directly to the etrailer Single Axle Trailer Fender w/ Side Steps - Black Plastic - 13" Wheels - Qty 1 #HP93RR. I reached out to the team that in charge of our etrailer parts…

view full answer...

Answer 9

I'd be happy to help you with that. For starters, the #F008584-2 fenders you'd looked at are designed for 14 inch wheels, you'd be better served going with the #F008585-2 which are designed for 15 inch wheels like the ones you have.…

view full answer...

Answer 10

There is an option like the Flint Hill Goods #FHG84ZR which would work with 1-7/8" and larger hitch ball couplers, but there is no dolly that'll work with a pintle hook on a trailer. The #FHG84ZR includes a 1-7/8" hitch ball, though you…

view full answer...

Answer 11

The Flint Hill Goods Trailer Dolly part #FHG84ZR will sit inside a 2" coupler but the coupler won't be able to latch so it could just pop off. If you want to use this dolly with a trailer that has a 2" coupler, I recommend replacing the…

view full answer...

Answer 12

If your trailer has a 2 inch coupler then you definitely need to go with a 2 inch ball. Even though 1/8 inches doesn't sound like very much, it is enough that your trailer could come uncoupled under the right conditions. I have attached a link to…

view full answer...

Mounting Brackets for Fulton Trailer Fenders # F008592

Products Featured in This Question

Continue Researching