Dimensions of the Lift Extenders for HappiJac Truck Camper Jack Systems Tube

Question

Question:

What is the dimensions of the tubes used for support?

asked by: Peter

0

Expert Reply:

I contacted the manufacturer about the dimensions of the Lift Extenders for HappiJac Truck Camper Jack Systems # LC182495. They informed me that the Lift Extenders for HappiJac Truck Camper Jack Systems # LC182495 are made from the same tubing used to make the inner leg of the camper jack and that the tube is 1.75” square.

expert reply by: Scott S

0

HappiJac Lift Extender Dimensions
(click to enlarge)

Answer 1

The distance between the mounting holes of the Lift Extenders for HappiJac Truck Camper Jacks #LC182495 that you referenced is 3-1/8 inches on center.

view full answer...

Answer 2

Hey Michael! The Pacbrake Alpha XD Pro Air Bag Suspension Kit w/ Internal Jounces #PB54TV includes two Schrader valves. A line will run from each air bag to its own valve so you can control them independently. This allows for the most customizable…

view full answer...

Answer 3

The HappiJac Electric Truck Camper Jack System #LC736515-ELKIT is the current replacement for the HappiJac 4800 series jacks. This is an upgrade as it includes the electric motor versus the HappiJac Manual Truck Camper Jack System #LC736515-4 which…

view full answer...

Answer 4

You typically only need them on the front Reid. The HappiJac Extender Bracket for Dual Wheel Chassis Truck Camper Jacks item #HJ54FR are going to give you the necessary clearance to back your dually truck up so you can drop your camper in the bed.…

view full answer...

Answer 5

I sure do Cynthia. If you take a look at the pictures I attached below, you'll see the Swing Out Extension Brackets item #LC182496 installed. The picture of the front of the camper also has the HappiJac Extender Bracket item #HJ54FR. These are…

view full answer...

Answer 6

The best chock/leveling system we have for your motorhome with a dually axle is the Andersen Camper Wheel Chock and Leveler part #AM3604. This system can be used on trailers/vehicles up to 30,000 lbs with wheels up to 32" diameter. They are made…

view full answer...

Answer 7

The actual outside width measurement of the MORryde Sliding Tray for RV Cargo Compartment - 72" x 20" x 6-5/8", #MR74FR, is 19.74". It has an interior measurement of 16.85".

view full answer...

Answer 8

Thanks for your question, Eddie. The short answer is yea, you can install the Pacbrake air bags with on board air compressor and 2-1/2 gallon tank, part #PB77SV. However, there are a few things to keep in mind. Since your truck is equipped with the…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

Hey Craig, thanks for reaching out. Yes, they will! The TorkLift StableLoad Suspension Upgrade #TLA7200 will indeed work with the Timbren bump stops on your 2025 Chevy 3500HD. The StableLoads mount under the overload spring, while the bump stops…

view full answer...

Dimensions of the Lift Extenders for HappiJac Truck Camper Jack Systems Tube

Product Page this Question was Asked From

Continue Researching