Replacement Double Lip Grease Seal for Kodiak Disc Brake Kit # K2HR35DKG

Question

Question:

Would you please provide me with specifications / part number for dual lip bearing seals for the 10-inch Kodiac disc brake kit eTrailer Item No. K2HR35DKG?

asked by: Tony L

0

Expert Reply:

The replacement grease seal for the Kodiak disc brake kit part # K2HR35DKG that you referenced is the part # 58846.

expert reply by: Jameson C

0

Answer 1

To get the best braking power for your boat trailer you would want to have disc brakes on both axles. If you happen to be limited to one axle then you would want the rear outfitted. With a 5,000lb boat you likely have two 3,500lb torsion axles. The…

view full answer...

Answer 2

Based on the measurements you took it sounds like you nailed exactly what you are looking for. The Kodiak Disc Brake Kit #K2HR35DKG is great for occasional use on salt water or fresh water. Unless you use your trailer frequently in water than I…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Replacement Double Lip Grease Seal for Kodiak Disc Brake Kit # K2HR35DKG

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching